English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 69 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Leaky nozzle - how much to disassemble? Von -- on May 10, 21 1715 8 Paul New to 3D printing and Prusa Products. Is this... Von Taxane on May 10, 21 2923 7 Taxane Assembly completed and first print Von Andrew Weitzel on May 09, 21 1796 5 Andrew Weitze... Gap Fills Issue Von Rocky79 on May 09, 21 3121 18 Rocky79 y axis bearing noise at initial assembly Von cwbullet on May 08, 21 3384 8 john XYZ Calibration Issue Von -- on May 08, 21 1354 8 MinorMatt MK3S+ printing fan not working - cannot comple... Von Clarmrrsn on May 08, 21 2023 3 admpc scale units mm/inches Von -- on May 07, 21 3496 7 Jerry S Fan not spinning Von 3Delight on May 07, 21 3537 16 boulland.mich... Nozzle hits prints off after about 450mm Answered Von cwbullet on May 07, 21 14537 46 Milazzone First print quality feedback Von cwbullet on May 07, 21 1882 3 quody Test pattern is not sticking to heatbed Von cwbullet on May 07, 21 3292 27 CJSHayward Can't get first layer right Answered Von Veritas on May 07, 21 1696 5 Veritas Y-axis assembly issues / frame skew Von -- on May 07, 21 2234 6 hullcb How do I slice the Stanford bunny for my MK3S+... Von cwbullet on May 07, 21 2006 14 CJSHayward Z-screw covers Von -- on May 06, 21 1498 3 MinorMatt Heatbed / Meshbed center is lower then left an... Von -- on May 06, 21 1663 6 Stefan Build instructions terrible - could shave hour... Von -- on May 06, 21 2509 17 Boslaw Small holes (underextrusion?) and errors on la... Von -- on May 06, 21 2753 3 ishiharas First Layer Calibration Von Kodiak437 on May 06, 21 1767 7 Kodiak437 Seite 69 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Teilen: