English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 62 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Help before I send this thing back. Przez karl-herbert on Aug 06, 21 5870 39 Burrfree Can I upgrade to the belt tensioner on my mk3? Przez cwbullet on Aug 06, 21 1285 2 Miriam Was z-level calibration done correctly? Przez FlyingCog on Aug 05, 21 2135 5 FlyingCog Blobs issue Przez Rocky79 on Aug 04, 21 2959 12 Rocky79 Under/overextrusion, temperature? Przez ktm1090 on Aug 04, 21 3037 10 ktm1090 Uneven Print Przez cwbullet on Aug 04, 21 2338 11 Jacob How do I fix these uneven walls? Przez Mark Blasco on Aug 04, 21 5654 12 Mark Blasco Filament sticking to the nozzle Przez bobstro on Aug 03, 21 8448 10 Q Odd Shift at the top of the print Przez mgtarallo on Aug 02, 21 1335 7 mgtarallo Some questions about getting the first few lay... Przez Dan Rogers on Aug 02, 21 1713 2 Awong1214 Bad solid-infill but good top-solid-infill? Przez muzz on Aug 01, 21 1875 3 muzz Strange Vertical Lines on Flat Surfaces Answered Przez Tarek Sobh on Jul 31, 21 2768 4 Tarek Sobh Shifting layers Answered Przez Runaljod on Jul 31, 21 1628 5 Runaljod Not melting plastic Przez Brettwi on Jul 31, 21 4231 10 Brettwi What am I doing wrong? Przez Ringarn67 on Jul 30, 21 11094 53 gk Automatic bed leveling not working? Przez Peter M on Jul 30, 21 2182 2 Dull Solderin... Debugging and Calibration Przez Dan Rogers on Jul 30, 21 2858 3 NMR_Scientist Z calibration width Ok (1.1 mm) but square tes... Answered Przez Vincnet Diallo... on Jul 29, 21 1924 3 Vincnet Diall... First Print Calibration Przez cwbullet on Jul 29, 21 1693 2 Chris Stayte Prusa logo, my first print after building the ... Przez Diem on Jul 28, 21 3292 7 rmarin Strona 62 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: