English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 63 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author First layer calibration extruder not moving Przez Diem on Jul 09, 21 1361 2 FiLiPAzN Completed build - mystery part Answered Przez jsw on Jul 09, 21 1316 5 ellem Different Live Z for Different Spools? Przez cwbullet on Jul 09, 21 1183 4 Henry Nylon Material all over, no more part density Przez cwbullet on Jul 09, 21 2526 11 Daniel Repeating artifact on prints Przez Sadet on Jul 08, 21 1584 7 Sadet Error in Z-Steps Przez KMeyerson on Jul 08, 21 1964 3 KMeyerson Instructions to disassemble standard MK3S+ pri... Answered Przez ssill2 on Jul 07, 21 2344 4 CJSHayward Selftest stuck on waiting for nozzle and bed c... Przez karl-herbert on Jul 03, 21 1802 2 Dylan Martine... XYZ Calibration & First Layer Cal successful, ... Answered Przez karl-herbert on Jul 03, 21 2054 5 Jason_A Trying first prints, not going so well (I susp... Przez sylviatrilling on Jul 03, 21 1629 7 HappyCerberus Uneven first layer Przez DrGanti2000 on Jul 02, 21 1763 4 DrGanti2000 Original I3 Mk3s kit question. Przez Diem on Jul 01, 21 1429 2 Dink PLA not working, PETG working fine Answered Przez JesperRank on Jul 01, 21 1671 5 JesperRank Bed is touching the frame Answered Przez Millcopter on Jul 01, 21 1937 13 Millcopter Extruder prints for a few minutes then grinds ... Przez cwbullet on Jul 01, 21 1499 2 vanayad Z banding at different heights Przez Charlie paton on Jul 01, 21 1905 7 Charlie paton Adjusting in the center Przez KKarlsson on Jul 01, 21 1099 3 KKarlsson Noise - resonation of y cariage Przez Dan Rogers on Jun 30, 21 2436 7 Dejf Please move the tensioners Przez Dan Rogers on Jun 29, 21 1601 5 Sean Roach Belt Tension and Z Motor Noise? Przez Diem on Jun 28, 21 2335 6 Taki8888 Strona 63 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: