English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 51 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Assembly Finished, Startup Errors, Z-axis Stif... Przez Dan Rogers on Nov 29, 21 3373 12 RivCA print is not sticking to bed Answered Przez Robin on Nov 29, 21 1836 10 lennou Z-axis assembly step 7 problem(?) Przez Diem on Nov 29, 21 1223 2 sgomes Calibration -> First layer cal doesn't work Przez Sébastien on Nov 27, 21 1446 3 Sébastien First layer does not stick to print surface Przez Robin on Nov 27, 21 3342 17 Samut 3DBenchy Defects Przez LenJH on Nov 26, 21 1616 4 LenJH PLA Orange weird extrude issue, any advice? Przez Othila on Nov 24, 21 1135 7 Othila Issues loading filament Przez Waresdom on Nov 23, 21 1039 1 Waresdom Issues with first layer adhesion/dragging Przez Diem on Nov 23, 21 1306 5 cjmm First layer issue need advice on this please Przez Othila on Nov 23, 21 1021 9 Othila Spare parts questions Przez jsw on Nov 23, 21 1202 6 topdotter XYZ calibration print head too low; First laye... Przez Dan Rogers on Nov 23, 21 1253 5 topdotter First layer opinion Przez Buzz on Nov 22, 21 1498 6 Buzz Strange machine behaviour... No filament comin... Przez Kopplog on Nov 21, 21 1503 12 Kopplog XYZ Calibration failed refer to manual Przez Design Elevato... on Nov 20, 21 1830 16 Arne Bed Level Correction assistance Przez shikaku201 on Nov 20, 21 1954 10 shikaku201 Is Ethyl Alchohol 70% OK for cleaning? Or it h... Przez Eric E on Nov 19, 21 4563 6 Samut First few weeks of prints Przez Diem on Nov 19, 21 1373 3 Buzz Brand new factory assembled mk3s+. Z axis much... Przez Kuri on Nov 18, 21 2397 5 Kuri A 38x42 mm. hollow cylinder takes 6 hours 36 m... Przez Neophyl on Nov 17, 21 1801 9 Samut Strona 51 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: