English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 51 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Assembly Finished, Startup Errors, Z-axis Stif... Por Dan Rogers on Nov 29, 21 3373 12 RivCA print is not sticking to bed Answered Por Robin on Nov 29, 21 1836 10 lennou Z-axis assembly step 7 problem(?) Por Diem on Nov 29, 21 1223 2 sgomes Calibration -> First layer cal doesn't work Por Sébastien on Nov 27, 21 1446 3 Sébastien First layer does not stick to print surface Por Robin on Nov 27, 21 3342 17 Samut 3DBenchy Defects Por LenJH on Nov 26, 21 1616 4 LenJH PLA Orange weird extrude issue, any advice? Por Othila on Nov 24, 21 1135 7 Othila Issues loading filament Por Waresdom on Nov 23, 21 1039 1 Waresdom Issues with first layer adhesion/dragging Por Diem on Nov 23, 21 1306 5 cjmm First layer issue need advice on this please Por Othila on Nov 23, 21 1021 9 Othila Spare parts questions Por jsw on Nov 23, 21 1202 6 topdotter XYZ calibration print head too low; First laye... Por Dan Rogers on Nov 23, 21 1253 5 topdotter First layer opinion Por Buzz on Nov 22, 21 1498 6 Buzz Strange machine behaviour... No filament comin... Por Kopplog on Nov 21, 21 1503 12 Kopplog XYZ Calibration failed refer to manual Por Design Elevato... on Nov 20, 21 1830 16 Arne Bed Level Correction assistance Por shikaku201 on Nov 20, 21 1954 10 shikaku201 Is Ethyl Alchohol 70% OK for cleaning? Or it h... Por Eric E on Nov 19, 21 4563 6 Samut First few weeks of prints Por Diem on Nov 19, 21 1373 3 Buzz Brand new factory assembled mk3s+. Z axis much... Por Kuri on Nov 18, 21 2397 5 Kuri A 38x42 mm. hollow cylinder takes 6 hours 36 m... Por Neophyl on Nov 17, 21 1801 9 Samut Página 51 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Compartir: