English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 50 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author First Layer Comparison - Speed vs Quality Przez nathandmelton on Dec 30, 21 2492 1 nathandmelton Need instructions or help in assembly Przez Chicago Keri on Dec 29, 21 2244 2 harrydude PTFE tube and Hotend on MKS3+ Przez Mark_T on Dec 28, 21 1551 3 porova Suddenly very hairy print Przez Diem on Dec 28, 21 7947 12 bvolckae Repeated banding in vertical print Przez ChadBuilds on Dec 28, 21 1610 2 ChadBuilds Tea. Earl Grey. NOT! Przez 3Delight on Dec 27, 21 5932 24 CJSHayward Have I just destroyed my two day old Prusa?! Przez malarks on Dec 27, 21 2166 4 malarks Ghosting in front and back Answered Przez denkovic on Dec 26, 21 1980 4 denkovic Terrible prints on a Prusa- assembled MK3S+ Answered Przez cwbullet on Dec 26, 21 2016 4 e1miran UPDATE: Small holes in benchy 3d Przez Gilles M on Dec 24, 21 14136 36 bguenthe Mesh bed fail Przez Robin on Dec 23, 21 1544 4 Knox Swafford x-axis and extruder motor switched during asse... Przez Neophyl on Dec 23, 21 2006 3 steamboat321 First Layer: corner issues. Expected or someth... Przez BillR on Dec 22, 21 3010 10 BillR Imperfections on PEI bed transferring to print... Przez C87 on Dec 21, 21 2290 2 C87 Is Prusa telling me I should enroll in AA? Przez sylviatrilling on Dec 21, 21 1835 6 dorkshoei Error "off-road" printing ... ??? Przez sylviatrilling on Dec 21, 21 2617 13 BoBaCool MK3S+ went rogue (distortion, spaghetti) overn... Przez AndersK on Dec 21, 21 1491 4 Samut New kit Build Prints have wavy layer shift. Przez Emcull03 on Dec 21, 21 1496 2 Emcull03 Y belt alignment issue Przez Emcull03 on Dec 21, 21 4880 6 morf 2nd print newbie question, Print gunked up and... Przez Jerny on Dec 20, 21 1253 1 Jerny Strona 50 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: