English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 43 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Expected Dimensional Accuracy Da RinkyTav on Feb 23, 22 1548 2 RinkyTav First layer calibration, don't know what "perf... Da jdFin on Feb 23, 22 1184 3 jdFin Not filling properly Da Diem on Feb 22, 22 1015 4 missgeneralid... SD card prints with Kits Da missgeneralide... on Feb 22, 22 4061 5 missgeneralid... First layer calibration Da Drillenissen on Feb 22, 22 1326 3 Drillenissen Adhesion of print to raft Da Diem on Feb 22, 22 1061 2 Kyle723 Thumps once at startup Da alianora on Feb 19, 22 1404 3 alianora mintemp error, hotend killed ? Da Max on Feb 19, 22 4380 23 Max what is this? Da Bob on Feb 18, 22 1448 8 John Is my x-belt tension too loose? Da xilex on Feb 18, 22 1494 3 xilex First layer problem with PETG - Irregular resu... Answered Da Txema on Feb 17, 22 3087 8 Txema Oops, success, oops again ... Da Diem on Feb 17, 22 2358 14 RoDavi recalibration? Da Diem on Feb 17, 22 1441 4 John What is a purpose of this nuts? Answered Da livius on Feb 15, 22 1645 4 livius Any idea whats wrong with my top layer? Da Robin on Feb 15, 22 1524 3 Zalgus First Layer Callibration Answered Da surgebox on Feb 15, 22 1717 4 surgebox Bed leveling question with these leveling valu... Answered Da Diem on Feb 15, 22 1468 4 xilex Odd Printing Issue Da cwbullet on Feb 15, 22 1589 2 durrettcustom... Waves in first layer Answered Da HappyKatz on Feb 14, 22 4163 5 HappyKatz Mk3S and adding MMU2.5S Assembly Instructions Da MikeJ on Feb 14, 22 1538 5 MikeJ Pagina 43 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Condividi: