English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 2 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Unable to Autoload Filament Od CodeCage on Apr 19 13562 9 gmbarton Last Mk3s+ to be built ? Od Dennis Jay on Apr 17 1942 2 Jws3d Superpinda keeps smacking print Od Eve on Apr 13 4109 2 CliffordTheRe... Inconsistent first layers after first few prin... Od Eve on Apr 13 3661 4 Eve Ultrasonic Cleaner on new bearings? Od TeamADW on Apr 09 4236 8 Bill Marcy Printer Failing Z-Axis Test With No Error Mess... Od Jake on Mar 21 3958 3 Jake First layer cal is way off Od Diem on Mar 13 3650 5 Bjerggaard No successful print so far Od FoxRun3D on Feb 28 3345 4 boricuastock Calibration Wizard question Od SWAG_4_1if3 on Feb 27 3353 3 SWAG_4_1if3 Whenever I run out of filament - I have to dis... Od dankat on Feb 25 4209 11 Mattias Fager... Argh! It keeps asking me to unload and reload... Od Deeb on Feb 22 18796 41 dimprov Priline Carbon Fiber Polycarbonate Not Good Od 3D2Reality on Feb 22 12199 14 Degreeless_En... Underextrusion / no extrusion at start of each... Od Green Joe on Feb 20 4162 5 Don Karnage XYZ Calibration Cube Od Robin_13 on Feb 17 2268 3 Iamcubsman PTFE tube Od Robin_13 on Feb 17 1713 4 Leo Extruder grub screw loose! Od Robin_13 on Feb 17 6413 11 Peter M Z banding? Need help Od Kharnberseker on Feb 17 2489 1 Kharnberseker Is it my nozzle or bed? Od Topaz Lazarus on Feb 14 2352 1 Topaz Lazarus Fine First layer calibration Od Diem on Feb 10 1863 9 latot Ground plate messy - first time this problem Od Fetzke on Feb 09 2334 3 Fetzke Stránka 2 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: