English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 118 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author X-Axis Problems Por Wuilt on May 11, 20 5222 12 stefan.e12 New MK3S, trouble with bench. Help please. Por Wilz on May 11, 20 1600 3 Wilz Filament hard to load then fails print during ... Por Matt Boyer on May 11, 20 1708 5 Matt Boyer First print failing after MMU2S Upgrade Por CovertPluto350... on May 10, 20 1720 2 Michael Y-axis belt alignment Por RH_Dreambox on May 10, 20 5215 4 VerianDarksta... Tree Frog Benchmark first print concerns (fres... Por rnisson@gmail.... on May 09, 20 2320 1 rnisson@gmail... Stepper Motor Only Turns One Direction Por markdeloura on May 08, 20 5216 13 Matt Kurek Grinding/Rattling sound from y-axis Por Hans Polders on May 08, 20 6261 4 Hans Polders Is this a First Layer Calibration issue? Por JBiz on May 08, 20 2805 7 JBiz Bed leveling issue Por Jordan on May 07, 20 1758 1 Jordan XYZ calibration failures and Y axis crashes Por Retired on May 06, 20 3438 12 MetalMangler Continuous extruding at the start of a print Por JoanTabb on May 06, 20 3124 9 rseal88 Linear Bearing Deformation? Por Patrick McNama... on May 06, 20 1475 3 Andy Ruth Inconsistency in Live-Z-Value Por RH_Dreambox on May 06, 20 2065 4 Flosten Oscillating temperature during print Por Govna on May 06, 20 1291 1 Govna Print sheet destroyed after removing headbands Por Milos V. on May 04, 20 2504 8 Juan Orlandin... New MK3S printed 20 hours, and stopped extrudi... Por wudi.pkueecs on May 03, 20 2031 5 wudi.pkueecs Power supply does not turn on. Por Zappovitz on May 02, 20 2842 5 Zappovitz Calibration XYZ Failed with MK3S Bear Answered Por graham_best on May 02, 20 10526 25 graham_best Problems with first layer (retractions, overex... Por sjlfabian on May 02, 20 3317 4 sjlfabian Página 118 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: