English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 118 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author New MK3S, trouble with bench. Help please. Od Wilz on May 11, 20 1598 3 Wilz Filament hard to load then fails print during ... Od Matt Boyer on May 11, 20 1701 5 Matt Boyer First print failing after MMU2S Upgrade Od CovertPluto350... on May 10, 20 1720 2 Michael Y-axis belt alignment Od RH_Dreambox on May 10, 20 5206 4 VerianDarksta... Tree Frog Benchmark first print concerns (fres... Od rnisson@gmail.... on May 09, 20 2315 1 rnisson@gmail... Stepper Motor Only Turns One Direction Od markdeloura on May 08, 20 5209 13 Matt Kurek Grinding/Rattling sound from y-axis Od Hans Polders on May 08, 20 6253 4 Hans Polders Is this a First Layer Calibration issue? Od JBiz on May 08, 20 2804 7 JBiz Bed leveling issue Od Jordan on May 07, 20 1757 1 Jordan XYZ calibration failures and Y axis crashes Od Retired on May 06, 20 3430 12 MetalMangler Continuous extruding at the start of a print Od JoanTabb on May 06, 20 3118 9 rseal88 Linear Bearing Deformation? Od Patrick McNama... on May 06, 20 1473 3 Andy Ruth Inconsistency in Live-Z-Value Od RH_Dreambox on May 06, 20 2064 4 Flosten Oscillating temperature during print Od Govna on May 06, 20 1289 1 Govna Print sheet destroyed after removing headbands Od Milos V. on May 04, 20 2502 8 Juan Orlandin... New MK3S printed 20 hours, and stopped extrudi... Od wudi.pkueecs on May 03, 20 2029 5 wudi.pkueecs Power supply does not turn on. Od Zappovitz on May 02, 20 2840 5 Zappovitz Calibration XYZ Failed with MK3S Bear Answered Od graham_best on May 02, 20 10520 25 graham_best Problems with first layer (retractions, overex... Od sjlfabian on May 02, 20 3316 4 sjlfabian Initial calibration fails - The extruder movem... Od lee on May 02, 20 2610 5 lee Stránka 118 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: