English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Page 116 / 195 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Suivant Titre du sujet Dernier message Nombre de vues Messages Author Rough surface finish on Mini 3D prints, what's... Par BogdanH on Sep 27, 21 12971 7 Slice Access to files on SD card Par Thomas Lynch on Sep 25, 21 4723 18 Thomas Lynch Feature Request - Display Expected Filament Re... Par BogdanH on Sep 25, 21 2330 4 eldonb46 Health concern in using dehydrator to dry fila... Par JuniperJuniper on Sep 24, 21 6630 12 prusanewuser Blobs of melted filament are fouling my print ... Par BogdanH on Sep 24, 21 7446 6 Marc Prusament orange headaches (underextrusion) Answered Par franksemi on Sep 23, 21 2638 7 Edwin Tuning the PC Blend Carbon Fiber profile Answered Par imhavoc on Sep 22, 21 2695 3 imhavoc remove requirement to add title if you add a r... Par bobstro on Sep 19, 21 1729 7 phidippus_fan General Printer Capabilities Question Par bobstro on Sep 19, 21 2423 8 MileHigh3Der is it possible to downgrade a firmware? Par bmorel on Sep 19, 21 6996 4 bmorel PETG edges peeling off Par Diem on Sep 18, 21 3108 4 Sander Prints failing midway through Par 3D_Printer_134... on Sep 18, 21 3788 5 3D_Printer_13... "M200 not supported" - GCODE upload error Par bobstro on Sep 17, 21 2810 2 FoxRun3D Using Prusa Mini for 3D positioning Answered Par JoanTabb on Sep 16, 21 2726 11 electronjohn PC Blend Carbon Fiber - heavy oozing Par imhavoc on Sep 16, 21 3108 10 imhavoc Timelapse Par cwbullet on Sep 15, 21 1850 4 Todd31 Prusament and Tough PLA? Par jsw on Sep 13, 21 3329 2 Ty Mechanical parts - Layer adhesion - Filament Par CountrySmile on Sep 13, 21 3291 6 jmf1 Firmware Mk2.5s Rambo card without firmware Par samucasam34 on Sep 13, 21 2157 1 samucasam34 prusaslicer print settings Par Mishel on Sep 12, 21 2276 4 Mishel Page 116 / 195 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Suivant Partager :