English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 20 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Tytuł Tematu Ostatni Post Widok Posty Author Disaster first layer Przez Chris Laudermi... on Jan 05, 22 2629 7 Spock Stringing test fail Przez Richy73 on Jan 04, 22 2681 18 Richy73 Printed object being bumped/dislodged by print... Przez Diem on Jan 04, 22 4278 12 sunnydevelope... Calibration cube prints 80% and then is pulled... Przez Diem on Jan 04, 22 3042 13 Tom Henry First test print but can't quite tell if Z axi... Answered Przez Gargs454 on Jan 03, 22 2097 3 Gargs454 Bed not centered? Przez huleboer on Jan 01, 22 1841 3 huleboer How to access x-axis pulley Answered Przez Armaan Sengupt... on Jan 01, 22 2066 3 T7MaMo PEI Bubbling Up Answered Przez BogdanH on Jan 01, 22 1899 2 fub Trouble recalibrating after maintenance Przez Bob on Jan 01, 22 1811 3 Staples323 Filament jammed inside Extruder-Rear (next to ... Przez JoanTabb on Dec 31, 21 1378 3 Blighty "Strange" Warping Przez Eric Eichstaed... on Dec 30, 21 1914 3 Eric Eichstae... Live Adjust Z Offset and PrusaSlicer Answered Przez Jemison on Dec 30, 21 3920 8 Jemison Help me with my adjustments Przez cwbullet on Dec 29, 21 1501 2 Faheygf Some thoughts as a new user Przez Distinctly Ave... on Dec 29, 21 1570 6 Distinctly Av... I'll admit I am frustrated Przez alidonkaka6 on Dec 29, 21 2199 7 greylock23 Seams in prints - Please Help! Answered Przez drraisin on Dec 28, 21 4269 7 Tgett 5 Failed 1st Print Attempts Przez BogdanH on Dec 28, 21 2116 7 Stuart Druckkopf drückt ins Bett Przez karl-herbert on Dec 26, 21 1756 2 Swedenchatter Printer stopped printing at 80% progress Przez benmc on Dec 26, 21 2499 2 Til Z axis 'jumping' during print? Przez languer on Dec 24, 21 6424 8 Gordanfreman Strona 20 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Share: