StephanK – Activité – Prusa3D Forum

Notifications

Clear all

StephanK

Groupe: Enregistré

A(ont) rejoint: 2016/10/05

Reputable Member

	Neal, I've had mixed results with Prusa support myself.. bu... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	You'd have to peel off the PEI sheet and attach a new one. ... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	Some more ideas: - are you still using the crappy original ... Dans le forum Others (Archive)	il y a 8 years
	Theres no easy fix to reduce this so called "Z-Scar". Printi... Dans le forum Others (Archive)	il y a 8 years
	Pasquale, you might get better help someplace where Geetech... Dans le forum Others (Archive)	il y a 8 years
	I am a bit puzzled. Not sure i understand what i am seeing t... Dans le forum Others (Archive)	il y a 8 years
	Did you check the usually fixes for layer shifting? Loose p... Dans le forum Ostatní (Archiv)	il y a 8 years
	Your biggest problem is the size: your design is 24x20x12, t... Dans le forum Print tips (Archive)	il y a 8 years
	Try dripping a little Isoprop Alcohol along the edges of the... Dans le forum Print tips (Archive)	il y a 8 years
	The command to stop heating the bed is M140 S0 It gets iss... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	My MK2 shows temperatures about +7°C too high, both for bed ... Dans le forum Others (Archive)	il y a 8 years
	What is that white stuff on your bed? Glue? And you are prin... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	If you order 2 rolls of HIPS at Trijexx Germany ( ) you get... Dans le forum Others (Archive)	il y a 8 years
	If XYZcalibration still was flaky , lowering the pinda some ... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	Sounds about normal for an "untuned" hotend. That's about wh... Dans le forum Others (Archive)	il y a 8 years
	If i hold something metal to it I can see that the light tur... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	Here's some more info on "elephant foot": When you say ... Dans le forum Others (Archive)	il y a 8 years
	The heat bed is in a hidden section of the Prusa shop only v... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	Eh, don't worry just yet. These little bumps go away in no t... Dans le forum Prusa i3 kit (Archive)	il y a 8 years
	Looks like the Z-Scar, printing slower should help. Playing ... Dans le forum Prusa i3 kit (Archive)	il y a 8 years

Page 10 / 21 Précédent Suivant

Statistiques du forum

566 Forums

63.2 K Sujets

444.3 K Messages

23 En-ligne

68.1 K Membres

Le dernier des messages: Poll - Should Prusa make the $299 MK4S -> Core One voucher available to all who purchsed the MK4S or MK4 to MK4S upgrade kit. Notre nouveau membre: etiennep Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé