ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	Ok, I'm getting back to this. About to try this model In En... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@axion it had just gotten the first layer down. so not much... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@axion I just started it printing a bit ago, but I'm going t... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@axion yeah I'm guessing the amount of infill as well. 5% m... Dans le forum How do I print this? (Printing help)	il y a 5 years
	the square pegs look pretty rough too. and they don't in th... Dans le forum How do I print this? (Printing help)	il y a 5 years
	How did you make that model? Besides that, 5% infill looks... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@axion The model looks strange when sliced you do have 7 to... Dans le forum How do I print this? (Printing help)	il y a 5 years
	you might zip up your .3mf file and attach here so folks can... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@ringarn67 I had the same issue and a thorough scrub with da... Dans le forum How do I print this? (Printing help)	il y a 5 years
	so my print failed again. part of it was I need to reslice ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@karalt After working with support for a few days and checki... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@karalt I was doing 215c Dans le forum How do I print this? (Printing help)	il y a 5 years
	@karaltThat super slow. I don’t think you should have to go... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@mdjuan Yes I understand the temperature difference but prus... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@karalt when I was doing PLA and BVOH I was just using the s... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Ok, so I made a small change to filament path and updated th... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@karalt Well I will say, I did NOT have good success with PE... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@karalt Had a few interventions so far with the bvoh. I upp... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@trevor-wilkins Listen to swiss 🙂 He knows what he's talki... Dans le forum How do I print this? (Printing help)	il y a 5 years
	No cooling fan gives you best layer bonding but least good-l... Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 68 / 104 Précédent Suivant

Statistiques du forum

598 Forums

71.8 K Sujets

504 K Messages

13 En-ligne

83.1 K Membres

Le dernier des messages: Under-extrusion in certain layers, depending on the PETG prints Notre nouveau membre: Print2Many Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé