ssill2 – Actividad – Prusa3D Forum

Avisos

Vaciar todo

ssill2

Grupo: Registrado

Registrado: 2021/01/18

Noble Member

	Ok, I'm getting back to this. About to try this model In En... En el foro How do I print this? (Printing help)	hace 5 years
	@axion it had just gotten the first layer down. so not much... En el foro How do I print this? (Printing help)	hace 5 years
	@axion I just started it printing a bit ago, but I'm going t... En el foro How do I print this? (Printing help)	hace 5 years
	@axion yeah I'm guessing the amount of infill as well. 5% m... En el foro How do I print this? (Printing help)	hace 5 years
	the square pegs look pretty rough too. and they don't in th... En el foro How do I print this? (Printing help)	hace 5 years
	How did you make that model? Besides that, 5% infill looks... En el foro How do I print this? (Printing help)	hace 5 years
	@axion The model looks strange when sliced you do have 7 to... En el foro How do I print this? (Printing help)	hace 5 years
	you might zip up your .3mf file and attach here so folks can... En el foro How do I print this? (Printing help)	hace 5 years
	@ringarn67 I had the same issue and a thorough scrub with da... En el foro How do I print this? (Printing help)	hace 5 years
	so my print failed again. part of it was I need to reslice ... En el foro How do I print this? (Printing help)	hace 5 years
	@karalt After working with support for a few days and checki... En el foro How do I print this? (Printing help)	hace 5 years
	@karalt I was doing 215c En el foro How do I print this? (Printing help)	hace 5 years
	@karaltThat super slow. I don’t think you should have to go... En el foro How do I print this? (Printing help)	hace 5 years
	@mdjuan Yes I understand the temperature difference but prus... En el foro How do I print this? (Printing help)	hace 5 years
	@karalt when I was doing PLA and BVOH I was just using the s... En el foro How do I print this? (Printing help)	hace 5 years
	Ok, so I made a small change to filament path and updated th... En el foro How do I print this? (Printing help)	hace 5 years
	@karalt Well I will say, I did NOT have good success with PE... En el foro How do I print this? (Printing help)	hace 5 years
	@karalt Had a few interventions so far with the bvoh. I upp... En el foro How do I print this? (Printing help)	hace 5 years
	@trevor-wilkins Listen to swiss 🙂 He knows what he's talki... En el foro How do I print this? (Printing help)	hace 5 years
	No cooling fan gives you best layer bonding but least good-l... En el foro How do I print this? (Printing help)	hace 5 years

Página 68 / 104 Anterior Siguiente

Estadísticas del Foro

598 Foros

71.8 K Temas

504 K Respuestas

13 En línea

83.1 K Miembros

Último Mensaje: Under-extrusion in certain layers, depending on the PETG prints Nuestro miembro más reciente: Print2Many Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado