ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	@quing As far as I've been told, the gauge that tests built ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@quing once you can print again you can print a tool in Prus... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@quing Interesting. have you checked the filesystem. I don... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@quing it does that, but if you click on the link you'll see... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I bought both my units assembled so I'm only guessing here. ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	if it's saying the file is incomplete that's definitely a cl... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@quing try adding media to insert into your post. Dans le forum How do I print this? (Printing help)	il y a 4 years
	@lvet Keep an eye out for for prusaslicer 2.4! It has pain... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@popepanator Waiting with bated breath! I'll definitely be... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Ok, so this seems like it might be working... The 2.4.0 slic... Dans le forum General discussion, announcements and releases	il y a 4 years
	@swiss_cheese You're right lol I forgot to switch to it. La... Dans le forum How do I print this? (Printing help)	il y a 4 years
	First make sure IR sensor and Finda are calibrated. Second, ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@aharbick Once you've your mintemp issue resolved make sure ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Support suggested I run my print with the Sensor info showin... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	you definitely have to have both the finda and the ir sensor... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	So I've been working with support. It turns out I may have ... Dans le forum General discussion, announcements and releases	il y a 4 years
	The 2.4.0 Prusaslicer allows you to paint the model based on... Dans le forum General discussion, announcements and releases	il y a 4 years
	The 0 degree alignment and ironing actually was less clear. Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese A number of those settings have been changed o... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@cwbullet Never regret that! I need one! lol Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 69 / 100 Précédent Suivant

Statistiques du forum

595 Forums

68.8 K Sujets

481.6 K Messages

12 En-ligne

77.5 K Membres

Le dernier des messages: PETG fine, but bad warping issues with PLA Notre nouveau membre: HaydenWizard Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé