ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	I'm wondering if now that my zOffset is what it should be if... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Aaaaaand.... FAIL Anyone have any clue what I might be missi... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Correction, .89. so a small piece of filament show up whe... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@cwbullet I have a print going of the light socket shelf in ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Here's what finally worked for me. I do get warping on one ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@cwbullet I had to make the extrusion multiplier on the para... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Mine did have one corner lift. oh well. might do a brim m... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stewartr this is great info! thank you very much! Here's w... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stewartr thanks for the heads up about MMU. it was an 8 we... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stewartr yeah, I'm doing something similar with a model of ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stewartr hey, I say if I have to wear a mask, I might as we... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I think this is a pretty standard issue. I think solutions... Dans le forum How do I print this? (Printing help)	il y a 5 years
	so I did get this to print. I wasn't crazy about the qualit... Dans le forum How do I print this? (Printing help)	il y a 5 years
	In my case I only use the PEI sheet since I want the smooth ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@peter-m-3 After working over a couple days with @swiss_chee... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese You were a great help! I've since printed an... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese I'm going to call this success. I even print... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese About to kick off print with the settings I pr... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I think I've found a setting that works. zOffset up one tick... Dans le forum How do I print this? (Printing help)	il y a 5 years
	So just as a test I took the square I've been using to calib... Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 100 / 104 Précédent Suivant

Statistiques du forum

598 Forums

71.8 K Sujets

504.1 K Messages

13 En-ligne

83.2 K Membres

Le dernier des messages: Mini LCD cable replacement Notre nouveau membre: Print2Many Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé