ssill2 – Actividad – Prusa3D Forum

Avisos

Vaciar todo

ssill2

Grupo: Registrado

Registrado: 2021/01/18

Noble Member

	@stewartr hey, I say if I have to wear a mask, I might as we... En el foro How do I print this? (Printing help)	hace 5 years
	I think this is a pretty standard issue. I think solutions... En el foro How do I print this? (Printing help)	hace 5 years
	so I did get this to print. I wasn't crazy about the qualit... En el foro How do I print this? (Printing help)	hace 5 years
	In my case I only use the PEI sheet since I want the smooth ... En el foro How do I print this? (Printing help)	hace 5 years
	@peter-m-3 After working over a couple days with @swiss_chee... En el foro How do I print this? (Printing help)	hace 5 years
	@swiss_cheese You were a great help! I've since printed an... En el foro How do I print this? (Printing help)	hace 5 years
	@swiss_cheese I'm going to call this success. I even print... En el foro How do I print this? (Printing help)	hace 5 years
	@swiss_cheese About to kick off print with the settings I pr... En el foro How do I print this? (Printing help)	hace 5 years
	I think I've found a setting that works. zOffset up one tick... En el foro How do I print this? (Printing help)	hace 5 years
	So just as a test I took the square I've been using to calib... En el foro How do I print this? (Printing help)	hace 5 years
	I wonder if that change from 230 on the first layer to 240 o... En el foro How do I print this? (Printing help)	hace 5 years
	Alas I spoke too soon. Big glob of started getting pushed a... En el foro How do I print this? (Printing help)	hace 5 years
	first layer going down perfectly En el foro How do I print this? (Printing help)	hace 5 years
	Not looking forward to doing this process again for the ninj... En el foro How do I print this? (Printing help)	hace 5 years
	@swiss_cheese In process. Fingers crossed En el foro How do I print this? (Printing help)	hace 5 years
	@dan-rogers I've been working with swiss_cheese the last cou... En el foro How do I print this? (Printing help)	hace 5 years
	@swiss_cheese yeah it's super smooth. attached is the corne... En el foro How do I print this? (Printing help)	hace 5 years
	The good thing is that by -.300 the lines are completely fus... En el foro How do I print this? (Printing help)	hace 5 years
	and here's the whole print. -.300 seems pretty good. shoul... En el foro How do I print this? (Printing help)	hace 5 years
	@swiss_cheese Alright, here we go. 011738c65baa795... En el foro How do I print this? (Printing help)	hace 5 years

Página 100 / 103 Anterior Siguiente

Estadísticas del Foro

595 Foros

70.3 K Temas

491.9 K Respuestas

18 En línea

81.6 K Miembros

Último Mensaje: Printing large flat panels vertically instead of horizontally? Nuestro miembro más reciente: Tocri77 Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado