ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	@neophyl ah. I'll have to check that out. That's one of ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@neophyl Odd, I have the scene units set to millimeters. ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Here's another pic of the failure. I'm tempted to try the 2... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@dan-rogers the screen shot was only showing half the print.... Dans le forum How do I print this? (Printing help)	il y a 5 years
	The above is 10mm tall with text starting at 2mm and ending ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	With blender 2.9.1 I've not tried to print this yet, but in... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stewartr I might have to try rigging this up. I've not had... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stewartr Well described sir! Dans le forum How do I print this? (Printing help)	il y a 5 years
	@gilles-4 the real test is print a model that's exactly one ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@neophyl yep, being a noob at this I felt really dumb when I... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@neophyl Agreed. I just went through this whole exercise fo... Dans le forum How do I print this? (Printing help)	il y a 5 years
	The top layer above looked like it wasn't hot enough. You c... Dans le forum How do I print this? (Printing help)	il y a 5 years
	And failure again lol. No visible warping, or raised corner... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Ok so had one stray filament string, but off to the side. ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@neophyl There actually was visible bow in the middle of the... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I know how I'd do it in blender. I'm not familiar with how ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	alright, I'm dialing this zOffset back to -0.290. The PETG... Dans le forum How do I print this? (Printing help)	il y a 5 years
	it's .2mm layer thickness, pretty standard. With the printe... Dans le forum How do I print this? (Printing help)	il y a 5 years
	My guess is that prior to me refining the zOffset with @swis... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@cwbullet Any idea why it starts that late in the print? Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 99 / 104 Précédent Suivant

Statistiques du forum

598 Forums

71.8 K Sujets

504.1 K Messages

11 En-ligne

83.1 K Membres

Le dernier des messages: Mini LCD cable replacement Notre nouveau membre: Print2Many Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé