ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	Prusa's answer seems like should be possible to do .32mm Dans le forum How do I print this? (Printing help)	il y a 5 years
	@flashburn I've only been 3d printing for a couple months so... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@flashburn Looking in the 2.3 Prusa slicer for the built in ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@silvertonesx24-2 It could speed is too fast maybe. What te... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@greenhoe in my limited experience, I've found that I've not... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I'm not sure but can you reasonably do .3mm layer height wit... Dans le forum How do I print this? (Printing help)	il y a 5 years
	bob you are correct on the bed temp. the print looks ok, an... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Going to take another stab at this probably early next week.... Dans le forum How do I print this? (Printing help)	il y a 5 years
	And it's laying down the layers over the infill cleanly too.... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stellr The infill was at 80, I brought it down to 50 Dans le forum How do I print this? (Printing help)	il y a 5 years
	and it still looks crisp, even on the infill. Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro I ended up doing 205 for first layer and 200 for al... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro actually I got this working without messing with my... Dans le forum How do I print this? (Printing help)	il y a 5 years
	this is is also working directly on the plate, no glue stick... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@greenhoe I'm printing something right now in PLA and I'm re... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@greenhoe I've seen gaps like that if I had retraction too h... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Could those be where retractions are happening? Dans le forum How do I print this? (Printing help)	il y a 5 years
	@stellr Actually the Live Z adjust is available for at least... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro Hi Bob, I was looking at your website, and you have... Dans le forum How do I print this? (Printing help)	il y a 5 years
	but the price is right! and it's what I learned 3d animatio... Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 98 / 104 Précédent Suivant

Statistiques du forum

598 Forums

71.8 K Sujets

504.1 K Messages

11 En-ligne

83.1 K Membres

Le dernier des messages: Mini LCD cable replacement Notre nouveau membre: Print2Many Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé