ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	@alexb this is so eerily reminiscent of the issue I saw with... Dans le forum How do I print this? (Printing help)	il y a 5 years
	After getting the settings dialed in I had good success. I'... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I agree with dan about the zOffset. if this is off, you wo... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese I agree! Your advice on this a few weeks ago ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I will share my experience on the very same issue which I ha... Dans le forum How do I print this? (Printing help)	il y a 5 years
	If you're already taking it in the shorts for that sub, yes ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I will say that after printing TPU(Ninjaflex) again this mor... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@terry-8 I've only been printing a few months also and had t... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@xaimav yeah, dawn plantinum plus simple dish sponge scrubbe... Dans le forum How do I print this? (Printing help)	il y a 5 years
	And of course hannibal mask with these settings fails... An... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Installed lol Dans le forum How do I print this? (Printing help)	il y a 5 years
	@cwbullet yeah I will later today. unfortunately work is g... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@cwbullet Shelf for my wife's electric toothbrush, to get it... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Spoke too soon lol. I was sitting here and I noticed someth... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I used the following as a basic guide. Dans le forum How do I print this? (Printing help)	il y a 5 years
	@neophyl It was several things. I've attached the zipped .3... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Did finally get this to print. I have a profile that works ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@neophyl I do like their colors and I'm trying to standardiz... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@flashburn I've not tried to print at a .3mm layer height, s... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Just got another spool of the white Paramount3D PETG in. I... Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 97 / 104 Précédent Suivant

Statistiques du forum

598 Forums

71.8 K Sujets

504.1 K Messages

12 En-ligne

83.1 K Membres

Le dernier des messages: Mini LCD cable replacement Notre nouveau membre: Print2Many Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé