Recent Posts

Forums | Topics

Page 6 / 44 Prev Next

	Topic Title	Forum
	7X7 Mesh Bed Leveling much faster on new printer By TwoBallScrewBall 5 years ago \| Last Post: 2 days ago	Hardware, firmware and software help
	Hi, old thread, still same problem exists. I upgra... 2 days ago By Wolf8... Funny you should post now, spiff75. 🙂 Just recent... 2 years ago By J My understanding is that there are 2 super pindas... 2 years ago By koure... view all posts
	Unable to log in to PrusaSlicer By jan.d.slay 3 days ago \| Last Post: 2 days ago	PrusaSlicer
	Well, there it is again. Connection cut off withou... 2 days ago By jan.d... Seems to have been a temporary problem, probably a... 2 days ago By jan.d... I can no longer log in to PrusaSlicer 2.9.4. I k... 3 days ago By jan.d...
	Relay on GPio or is it passthrough By Alienbliep 3 weeks ago \| Last Post: 2 days ago	Prusa add-ons (GPIO, accelerometer,...)
	So to answer my own questions. Yes the GND on the ... 2 days ago By Alien... Does anybody know if the gnd point on the gpio is ... 3 weeks ago By Alien... So an little follow up. I went to the electronics ... 3 weeks ago By Alien... view all posts
	Can not get Buddy3D to connect By GaryBushey 4 days ago \| Last Post: 2 days ago	Hardware, firmware and software help
	I suspect that it was Prusa Direct or their connec... 2 days ago By jan.d... So I just checked again and it appears to be worki... 3 days ago By GaryB... It says it finds the QR code just fine. But once ... 3 days ago By GaryB... view all posts
	Flächen drucken fehlerhaft By schopp3r 4 days ago \| Last Post: 2 days ago	Hilfe zur Hardware, Firmware und Software
	Moin, welches Material, welche Temperaturen, welc... 2 days ago By Thoma... Hallo. Unser Prusa Mini+ hat nach dem Zusammenbau ... 4 days ago By schop...
	arrêt de la chauffe hotend après retrait filament? By Laurross 4 days ago \| Last Post: 2 days ago	Dépannage pour l'assemblage et les premières impressions
	Merci bcp, basique effectivement. Je m'attendais à... 2 days ago By Laurr... Bonjour, il n'y a pas d'âge pour découvrir de nouv... 3 days ago By Stald... Bonsoir Premier plongeon dans le 3dprint (a 65 bal... 4 days ago By Laurr...
	Nextruder assembly noise - Have others encountered this? By C.Tacchi 3 weeks ago \| Last Post: 2 days ago	Assembly and first prints troubleshooting
	So, since last assembly of the Nextruder the sound... 2 days ago By C.Tac... Quick follow-up... Looking at the instructions ag... 2 weeks ago By C.Tac... Pardon the delay in response - had to get to the o... 2 weeks ago By C.Tac... view all posts
	Lüftertest fehlgeschlagen By physics_teacher 2 days ago \| Last Post: 2 days ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Guten Morgen, der neue Prusa XL mit 5 Druckköpfen ... 2 days ago By physi...
	Is this a mod I should consider implementing By Phil 6 days ago \| Last Post: 3 days ago	User mods
	If you have a big difference between sides, then y... 3 days ago By abman... Unless you are getting consistent 1st layer proble... 5 days ago By hyige... I had an uneven bed as well. I moved Z to 275, dis... 5 days ago By Augen... view all posts
	Octoprint HTTPS Validation on Mac with 2.3.0 By scott-5 6 years ago \| Last Post: 3 days ago	PrusaSlicer
	Not sure if it's relevant, but 10 months on from t... 3 days ago By Tim S... 18 months on from the last post, I'm running into ... 10 months ago By kvand Have not looked into this in a while. Seems to be ... 2 years ago By Chris view all posts
	MK4S welche Düse für Mischbetrieb By airmel 3 days ago \| Last Post: 3 days ago	Hardware, firmware and software help
	Sie befinden sich in einem englischsprachigen Foru... 3 days ago By miros... Hallo. Welche Düse sollte ich in meinen MK4S am be... 3 days ago By airme...
	MK4S Blob-of-Death removed. Extruder OK? By ToddFerwerda 4 days ago \| Last Post: 3 days ago	Hardware, firmware and software help
	Putting the heating block in place is fun. It's wo... 3 days ago By miros... Thanks Joan, I'll tinker it back into place. 3 days ago By ToddF... the extruder / heatblock seems to have rotated 45 ... 3 days ago By JoanT...
	MK4S->CoreOne+ : Z treaded axis off-centered By Archalb 5 days ago \| Last Post: 3 days ago	Assembly and first prints troubleshooting
	Thank you for the great support 👍🏻 I successfully ... 3 days ago By Archa... We have a surface profilometer at work that uses a... 3 days ago By Conra... Many thanks for testing this -- and I am happy to ... 3 days ago By Jürge... view all posts
	Why is the quality of my nylon-cf prints getting progressively worse? By samfo 2 weeks ago \| Last Post: 3 days ago	How do I print this? (Printing help)
	Wear resistant just means that. CF and GF filament... 3 days ago By hyige... Wow, that's a lot of wear for a "wear resistant" n... 3 days ago By Conra... Interesting find! I only use Diamondback nozzles w... 3 days ago By hyige... view all posts
	Layer lines problem By Jwo 3 days ago \| Last Post: 3 days ago	General discussion, announcements and releases
	This, from Slant 3D, is a comprehensive explanatio... 3 days ago By brian... Hi, try "External perimeters first" option in "Adv... 3 days ago By PaKo Or search this forum for "buldge" (sic). Dozens of... 3 days ago By FoxRu... view all posts
	LCD goes into light mode on it's own By MTA angers 8 months ago \| Last Post: 3 days ago	Hardware, firmware and software help
	My XL just did the same. It's printing.. (26+ hour... 3 days ago By Meuon Hello,I've now had this happen a couple of times, ... 8 months ago By MTA a...
	Advanced Filtration and Chamber Fan Control By Hugh 3 days ago \| Last Post: 3 days ago	User mods
	If you have the advanced filtration installed on t... 3 days ago By Hugh
	Core One > Core One+ Upgrade - VIDEO GUIDE By iftibashir 3 days ago \| Last Post: 3 days ago	Assembly and first prints troubleshooting
	Full guide for the Core One to Core One+ Upgrade! ... 3 days ago By iftib...
	Prusa Core One - VIDEO BUILD GUIDE By iftibashir 9 months ago \| Last Post: 3 days ago	Assembly and first prints troubleshooting
	Core One build guide has been updated with the new... 3 days ago By iftib... Thank you. The video guide is supplemental materia... 2 weeks ago By iftib... Hi, From what I have seen so far, these are really... 2 weeks ago By MHfro... view all posts
	Z homing error By Bruce Labitt 5 days ago \| Last Post: 3 days ago	Hardware, firmware and software help
	I don't think one can get enough detail using sand... 3 days ago By Bruce... you might try ordinary sandcasting (two shells wit... 3 days ago By mnent... I agree that FDM printing is amazing. But those l... 3 days ago By Bruce... view all posts