Recent Posts

Forums | Topics

Page 3 / 37 Prev Next

	Topic Title	Forum
	Špatné nastavení teploty trysky? By Lukáš Duběda 1 year ago \| Last Post: 1 day ago	Složení tiskárny a řešení potíží s prvním tiskem
	MK4 na rozdíl od mk3 nemá kompenzaci teploty pro t... 1 day ago By pink_... Jak by to asi řešil? Odpověď je o příspěvek výše. ... 7 months ago By miros... Jak jste to nakonec vyřešili? 7 months ago By Adriá... view all posts
	Printables - Copy/Paste bug? By shrap 3 weeks ago \| Last Post: 1 day ago	General discussion, announcements and releases
	Following Tampermonkey script works for me: // ==U... 1 day ago By cwohl... I can confirm this happens for me as well on firef... 1 day ago By cwohl... that checks out as to why I probably wasn't seeing... 5 days ago By Geoff... view all posts
	Migrating MMU3 from Mk3S+ to Core One? By Patronics 2 months ago \| Last Post: 1 day ago	General discussion, announcements and releases
	I have the same question 1 day ago By Koos I think it's finally time to bite the bullet and r... 2 months ago By Patro...
	filament dryer By skylab9999 3 days ago \| Last Post: 1 day ago	General discussion, announcements and releases
	Fillamentum doesn't agrees with those drying tempe... 1 day ago By Artur... Desiccant type dryers (like silica gel units): The... 2 days ago By skyla... I still have a question, where does the moisture g... 2 days ago By Green... view all posts
	Nozzle temperature not correct By [email protected] 2 days ago \| Last Post: 1 day ago	Assembly and first prints troubleshooting
	Have replaced the thermistor with a new one, used ... 1 day ago By diete... Checked everything double. All connections done an... 1 day ago By diete... It's possible the thermistor in the heat block is ... 2 days ago By hyige... view all posts
	Problem z selftestem osi X (1 viewing) By pangus 1 day ago \| Last Post: 1 day ago	Hardware, firmware i oprogramowanie - pomoc
	Witam, przychodzę tutaj z problemem, który nie jes... 1 day ago By pangu...
	Manually adjust heat bed thermister calibration temp??? By Dazz 1 day ago \| Last Post: 1 day ago	Hardware, firmware and software help
	Hi I have replaced my heat bed thermister but now ... 1 day ago By Dazz
	Prusa Slicer settings for Anycubic Kobra S1 By Nolan 1 day ago \| Last Post: 1 day ago	General discussion, announcements and releases
	Was wondering if anyone had suggestions or config ... 1 day ago By Nolan
	Strange issues on prints By vsions 2 days ago \| Last Post: 2 days ago	Assembly and first prints troubleshooting
	It's a combination of extreme overhang and the dir... 2 days ago By Diem Hello, I have been trying to figure out why my pri... 2 days ago By vsion...
	Chronic Under-Extrusion - Core ONE By PaltrySun 2 days ago \| Last Post: 2 days ago	General discussion, announcements and releases
	Once you have consistently dry filament (and possi... 2 days ago By Diem Thanks for the responses! I only used PLA and P... 2 days ago By Paltr... clicking/grinding filament and stringy filament Ag... 2 days ago By Diem view all posts
	PrusaConnect keeps showing OFFLINE and other connection issues By Roger 6 months ago \| Last Post: 2 days ago	Bugs & Errors
	Same here, when starting up everything shows ok, a... 2 days ago By sabre... I've been having the same issues with my Core One.... 2 weeks ago By Hammy I'm still getting these Offline statuses, been hap... 3 weeks ago By Chris view all posts
	Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 1 month ago \| Last Post: 2 days ago	General discussion, announcements and releases
	I am having the same issue! Hope there's an answer... 2 days ago By Crise... That is correct. Any suggestions? 2 weeks ago By Dik H... Buddy Camera that’s linked to a Core device (maybe... 2 weeks ago By Deepa...
	Large ABS + PLA print, PLA keeps clogging By xatlas0 2 weeks ago \| Last Post: 2 days ago	General discussion, announcements and releases
	I experienced a similar issue with the combo of AS... 2 days ago By dawso... What's the best way to check size and roundness so... 2 weeks ago By Diem The three most likely causes: - Out of spec filame... 2 weeks ago By xatla... view all posts
	Core One skipping steps/Layer shift By Enrique Specht 6 months ago \| Last Post: 2 days ago	Hardware, firmware and software help
	I am having the exact same problem. The location o... 2 days ago By Jane ... I seem to have the same, or at least similar probl... 1 week ago By Marti... I am experiencing the same issue, with a printable... 1 week ago By wdvc view all posts
	Two head printing - Automatic switch By AAM Metaldyne 2 days ago \| Last Post: 2 days ago	How do I print this? (Printing help)
	You are looking for the Spooljoin function: Cheer... 2 days ago By Diem Hello, My compagny order a printer XL for indust... 2 days ago By AAM M...
	Core one firmware 6.4.0 alpha By Philippe BAUER 2 days ago \| Last Post: 2 days ago	Hardware, firmware and software help
	For the core one, concerning the phase stepping c... 2 days ago By Phili...
	Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App By Vincent5840 5 months ago \| Last Post: 2 days ago	Hardware, firmware and software help
	That's not entirely right. It may level the bed at... 2 days ago By CJD Thank you! 🙂 2 days ago By Timma... RE: Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App 2 days ago By Raine... view all posts
	MK4 Prusa Enclosure By Mullu 3 days ago \| Last Post: 2 days ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	danke für die schnelle Antwort. Ich bevorzuge die ... 2 days ago By Mullu Entweder den PTFE-Schlauch durch drücken von oben ... 3 days ago By Walte... Hallo, ich habe dieses Wochenende das Gehäuse für ... 3 days ago By Mullu
	CORE One: Funktion Türschalter? By M3T 6 days ago \| Last Post: 2 days ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Nach Kontakt mit Prusa des Rätsels Lösung: 1. Der ... 2 days ago By M3T Hallo, nach Inbetriebnahme des CORE One (Kalibrier... 6 days ago By M3T