English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Page 82 / 190 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Next Topic Title Last Post Views Posts Author Bad print settings or poor design? By -- on May 16, 21 1908 4 hawai The printout shifts by 10mm along the x-axis i... By ssill2 on May 15, 21 3238 15 christian Voronoi Pattern Printing without strings possi... By Swiss_Cheese on May 15, 21 4710 7 alexanderswo Please analyze print quality By Swiss_Cheese on May 15, 21 3386 6 Astroxss TPE print problems By Swiss_Cheese on May 13, 21 4002 16 DeltaWerks Need advice on troubleshooting my Benchy By MightWorks on May 13, 21 3990 9 MightWorks Problems printing with PETG first layer. By -- on May 13, 21 4647 15 Steve Gluing Help By -- on May 12, 21 2977 9 Big Buddha Benchy printing problem with PETG By Jimbo70 on May 12, 21 3248 6 Jimbo70 Printing with Prusa ABS-T By cwbullet on May 12, 21 3037 4 shay.s 1st layer issue? By Bob the Maker on May 12, 21 2028 4 Bob the Maker Corner warp/lifting By cwbullet on May 11, 21 5426 5 Jerry S Weird noise and print failing at same spot By dakiki on May 11, 21 2491 10 dakiki Brand New Official Hot End, Now Overhangs are ... By cwbullet on May 10, 21 2849 16 TwoBallScrewB... Damaged in bottom printing By -- on May 10, 21 2031 3 liubie Will printing nylon destroy my powder coated s... By arjan on May 09, 21 16987 20 Tellblom How to avoid these hollow lines (underextrusio... By -- on May 09, 21 9741 37 flux_capacito... Problem with ColorFabb PLA / PHA Filaments By SteveM on May 08, 21 3422 6 Rob PETG retraction settings By FoxRun3D on May 08, 21 11342 4 der_da PETG Stringing and broke my prusaprinter By cwbullet on May 08, 21 2845 9 offiRent Page 82 / 190 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Next Share: