English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 5 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author Bad "lines" when print almost horizontal surfa... Przez Peter on Dec 19 2212 6 Peter ESUN PETG Print Settings Answered Przez Constantin on Dec 18 14648 32 Rocky79 Printing 250mm wide - A toolpath outside the p... Przez Brad on Dec 17 9344 13 PorrdigeFacto... What Settings Should I Be Looking At? Przez parallon on Dec 17 1728 7 parallon Can I print multiple colors at the same layer? Przez Tiago Carvalho on Dec 16 33310 19 0mib How do I print each layer in same infill direc... Przez ufanders on Dec 16 25332 21 Bvdv Moving the nozzle wipe Przez dflipse on Dec 15 7212 9 DrAl Flat spots/bad finish separation on supported ... Przez Evan Judson on Dec 13 1050 3 Evan Judson Gaps on top layer of print Przez Brian on Dec 13 1490 3 mgantner How to improve overhangs on this print? Przez Diem on Dec 12 2344 2 Maciej Latuse... Having cyclic underextrusion. Suspect bontech ... Przez RedDawg on Dec 09 1633 4 RedDawg how do i stop curling Przez Friedham on Dec 08 23897 25 Cowen Blob of filament extruded when resuming from a... Przez Daniel Siffred... on Dec 07 9705 13 RichardLarson Peeling off outlines Przez MaiBo on Dec 07 1406 2 MaiBo Support Material For Openings on Part Przez Yngeinstn on Dec 05 1224 5 Yngeinstn Under extrusion after seam Przez jake181 on Dec 05 1441 1 jake181 0.8 Nozzle - over or under extrusion? Przez eleph67 on Dec 03 891 2 Basic HELP Przez Robin on Dec 02 953 2 alvaroachu Corner Bubbling and Rough Przez Friso Modderma... on Dec 01 2511 4 stokes776 Threads Przez alvaroachu on Nov 29 926 4 alvaroachu Strona 5 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: