Notifications
Clear all

Help with my Prints  

Stránka 2 / 2
  RSS
JoanTabb
(@joantabb)
Veteran Member Moderator
RE: Help with my Prints

@pablo-f-2

Have you tried the 

'Life Adjust 'Z' My Way'

process

https://forum.prusa3d.com/forum/original-prusa-i3-mk3s-mk3-assembly-and-first-prints-troubleshooting/life-adjust-z-my-way/

and are you using 7x7 mesh bed levelling, available on the LCD Display
it tests 49 points on the build plate instead of the normal 9 points... 

regards Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK

Napsal : 24/11/2020 7:10 pm
Pablo-F
(@pablo-f)
Active Member
Topic starter answered:
RE: Help with my Prints

@joantabb

 Yes i am Zaungast the Life Adjust 'Z' My Way'

but 7x7 49 points, no not yet.
thank you Joan 😊 

Napsal : 24/11/2020 10:41 pm
JoanTabb
(@joantabb)
Veteran Member Moderator
RE: Help with my Prints

Best wishes!

 

Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK

Napsal : 25/11/2020 2:03 am
Pablo-F
(@pablo-f)
Active Member
Topic starter answered:
RE: Help with my Prints

I think with soap cleaning and 7x7 mesh bed levelling i have a very good result of first layer.

Thank you all. 🙂

Napsal : 25/11/2020 11:05 am
JoanTabb
(@joantabb)
Veteran Member Moderator
RE: Help with my Prints

@pablo-f-2

excellent news...

however If you find the bottom layer of supports is now difficult to remove completely, you could consider adding a raft to tie the supports together and make them easier to get off the build plate... 

regards Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK

Napsal : 25/11/2020 2:38 pm
Pablo-F se líbí
Pablo-F
(@pablo-f)
Active Member
Topic starter answered:
RE: Help with my Prints

@joantabb

i am since one week into 3D printing, and i have no idea what a raft is or wehere i can make one. 🙂

I have to look that up somewhere.

I am using the auto support "everywhere" 

thank you very much Joan for your help

Napsal : 25/11/2020 2:48 pm
cwbullet
(@cwbullet)
Member
RE: Help with my Prints

@pablo-f-2

A raft is in the setting for PrusaSlicer.  

Here is a good rundown of what rafts are:

https://www.simplify3d.com/support/articles/rafts-skirts-and-brims/

--------------------
Chuck H
3D Printer Review Blog

Napsal : 25/11/2020 2:58 pm
Pablo-F se líbí
bobstro
(@bobstro)
Illustrious Member
RE: Help with my Prints

Fine first-layer supports as shown in the 1st post should be no problem on the smooth PEI sheet washed only with Dawn dish soap and no alcohol. By all means, try isopropyl alcohol. Don't just use a dampened cloth. Pour on a good squirt and give it a wipe. But if you still have adhesion problems, nothing beats a wash under the sink with plain dish soap.

 

My notes and disclaimers on 3D printing

and miscellaneous other tech projects
He is intelligent, but not experienced. His pattern indicates two dimensional thinking. -- Spock in Star Trek: The Wrath of Khan

Napsal : 25/11/2020 3:24 pm
Pablo-F
(@pablo-f)
Active Member
Topic starter answered:
RE: Help with my Prints

Here you can see the finish print

Napsal : 26/11/2020 12:30 pm
cwbullet
(@cwbullet)
Member
RE: Help with my Prints

@pablo-f-2

Pretty neat print.  Need to tighten up the setting and it might need different support settings.  

--------------------
Chuck H
3D Printer Review Blog

Napsal : 26/11/2020 12:38 pm
JoanTabb
(@joantabb)
Veteran Member Moderator
RE: Help with my Prints

I Guess your adhesion is sorted for the moment

regards Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK

Napsal : 26/11/2020 12:53 pm
Pablo-F se líbí
Pablo-F
(@pablo-f)
Active Member
Topic starter answered:
RE: Help with my Prints
Posted by: @cwbullet

@pablo-f-2

Pretty neat print.  Need to tighten up the setting and it might need different support settings.  

yes i think so too, need to find out more about support settings, maybe the new slicer will help 🙂

Napsal : 26/11/2020 2:37 pm
Pablo-F
(@pablo-f)
Active Member
Topic starter answered:
RE: Help with my Prints
Posted by: @joantabb

I Guess your adhesion is sorted for the moment

regards Joan

thank you Joan, until next time 😉 😆 

Napsal : 26/11/2020 2:38 pm
Stránka 2 / 2
Share: