English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 75 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Filament Extrusion Test Failure - Hot End Too ... Przez Peter M on Apr 02, 21 2451 15 Bill H New to this - First layer not sticking Przez Chris W. on Apr 01, 21 1585 5 Ambanja Y carriage noise? Przez Dan Rogers on Mar 31, 21 3101 15 Jordan Inconsistent first layer from a cold start to ... Przez TomDD on Mar 31, 21 2952 13 TomDD New Kit won't Run thru Self Test Przez smurpheod on Mar 31, 21 5148 22 Sam Problem printing a thin walled hollow cube Przez Dan Rogers on Mar 30, 21 3670 9 TwoBallScrewB... First layer - too low or too high? Przez wakareva on Mar 30, 21 2218 5 wakareva Lines in print on textured bed in various loca... Przez Diem on Mar 30, 21 2181 6 mgtarallo New here and printed the first item. Overal sa... Przez Clarmrrsn on Mar 29, 21 1732 3 FRANK Random X-offset Przez Clarmrrsn on Mar 29, 21 2818 6 JulietteLhx Hot End Replacement - Covered in Filament Blob Przez bobstro on Mar 29, 21 4995 4 Ed_ATL Strange issue with MK3S and Cura. At a loss. Przez jsw on Mar 28, 21 2684 7 760 Creations New MK3S+ First Prints and severe PETG warping... Przez noobmaker on Mar 28, 21 3597 20 noobmaker Batman holes / craters on the top layer Przez dark_NES on Mar 28, 21 9417 47 dark_NES Why are the print times almost the same when I... Przez bobstro on Mar 27, 21 7479 14 MTom Strange Problem - Layer shift only on top and ... Przez MadMax on Mar 27, 21 1835 5 MadMax Failed First Layer and completely molten Extru... Przez Peter M on Mar 27, 21 2348 9 Dennis Spiele... upgrading MK3 Przez Baklin on Mar 26, 21 1728 2 Larrya Problem printing Benchy - raised section hits ... Przez Technical Ted on Mar 25, 21 11472 41 Technical Ted Blobs or Zits? Przez prusanewuser on Mar 25, 21 14670 6 Raku76 Strona 75 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: