English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 76 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Bed leveling print issues Przez Clarmrrsn on Mar 20, 21 1060 2 Quarzk Bed Level Correction ( Factory assembled) Przez Philipp M on Mar 19, 21 978 3 Philipp M X-Axis error when properly tightening backplat... Answered Przez deathrayoflove on Mar 19, 21 1866 3 deathrayoflov... Frame Assembly- Flatness of surface required? Przez Clarmrrsn on Mar 19, 21 2471 10 Clarmrrsn Issue with maybe X-axis? Przez Clarmrrsn on Mar 18, 21 1408 5 Mut3ki Issue With Print Bed Przez Dan Rogers on Mar 18, 21 1644 6 Ricardo V Does i3MK3S+ require more negative values in 1... Przez Zoltan on Mar 18, 21 3744 26 prusanewuser E Axis Assembly Step 30 - PTFE Tubing Confusio... Przez Antonio on Mar 17, 21 1096 7 Bill H Belt Tension Too Tight Przez Technical Ted on Mar 16, 21 2657 6 Bill H Z-banding problem. Anyone recognize this probl... Przez Dan Rogers on Mar 16, 21 1360 7 Conor D Calibrate Z Fails Przez Clarmrrsn on Mar 16, 21 1065 4 Marauderz Is the IR sensor cable which came with the i3M... Answered Przez prusanewuser on Mar 15, 21 1325 3 prusanewuser XYZ Calibration error Przez Clarmrrsn on Mar 14, 21 1280 6 Eric What Is Wetting My Bed? Answered Przez JoanTabb on Mar 13, 21 1985 8 Taken4Granted Model detaches during print Przez Nordestgaard on Mar 13, 21 2379 5 Nordestgaard New printer, frequent failures with "Crash det... Przez Diem on Mar 13, 21 2037 5 Oleg Benchy first print fail twice Przez Technical Ted on Mar 13, 21 7208 12 Gemini1364 Benchy failing at top of door arches Przez Technical Ted on Mar 12, 21 5430 3 Trusted Devel... First layer issues Przez jaskew on Mar 12, 21 2572 17 jaskew Extruder Assembly, Gears do not line up. Przez CrosswindJones on Mar 10, 21 2097 4 CrosswindJone... Strona 76 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: