English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 74 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Strange issue with MK3S and Cura. At a loss. Przez jsw on Mar 28, 21 2082 7 760 Creations New MK3S+ First Prints and severe PETG warping... Przez noobmaker on Mar 28, 21 2569 20 noobmaker Whenever I run out of filament - I have to dis... Przez Martijn Jansse... on Mar 28, 21 3040 10 Mattias Fager... Batman holes / craters on the top layer Przez dark_NES on Mar 28, 21 5856 47 dark_NES Why are the print times almost the same when I... Przez bobstro on Mar 27, 21 5477 14 MTom Strange Problem - Layer shift only on top and ... Przez MadMax on Mar 27, 21 1303 5 MadMax Failed First Layer and completely molten Extru... Przez Peter M on Mar 27, 21 1837 9 Dennis Spiele... upgrading MK3 Przez Baklin on Mar 26, 21 1467 2 Larrya Problem printing Benchy - raised section hits ... Przez Technical Ted on Mar 25, 21 8525 41 Technical Ted Blobs or Zits? Przez prusanewuser on Mar 25, 21 13233 6 Raku76 Issue sticking to the bed Przez Clarmrrsn on Mar 24, 21 1876 19 Dazza Printer literally sounds like a dial up modem Przez Diem on Mar 24, 21 3664 11 Mydayyy First layer calibration help for kit build Przez danderson on Mar 24, 21 1874 5 danderson Calibration fail Przez 3Delight on Mar 23, 21 1536 4 Maneria Is my Filament Sensor Toast? Przez Clarmrrsn on Mar 23, 21 1093 2 Jay First Layer Calibration = Nothing and then a M... Przez Diem on Mar 22, 21 1485 7 Joe B SO sad. Przez Clarmrrsn on Mar 22, 21 2689 8 3dNoob First Prints Answered Przez Clarmrrsn on Mar 22, 21 1061 7 Clarmrrsn surface problem Przez Neophyl on Mar 22, 21 1677 4 staccio X-axis and the trapezoidal nuts Przez Eyebrowz on Mar 22, 21 1791 2 Eyebrowz Strona 74 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: