English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 73 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Thick layer line on same area of multiple prin... Przez Dan Rogers on Apr 08, 21 1691 4 tentaclejoe Isolation on the cables near the hotend. Przez Zbyszek on Apr 06, 21 1578 7 Zbyszek First print - what is wrong? Przez cwbullet on Apr 05, 21 1878 4 OndrejS First layer smaller than second Answered Przez Neophyl on Apr 04, 21 2914 2 Christos.Tzer... Screwed up doing assembly, how to solve and wh... Przez cwbullet on Apr 03, 21 2274 11 Reas Set up process not starting Przez Neophyl on Apr 03, 21 1617 2 grizzly99 Can't print PLA Przez Peter M on Apr 03, 21 2072 6 kirkfrey ripples on flat surface PLA Przez Peter M on Apr 03, 21 2492 2 kabauter My First print - Any advise? Przez Clarmrrsn on Apr 02, 21 1845 8 Djidji Filament Extrusion Test Failure - Hot End Too ... Przez Peter M on Apr 02, 21 1746 15 Bill H New to this - First layer not sticking Przez Chris W. on Apr 01, 21 1075 5 Ambanja Y carriage noise? Przez Dan Rogers on Mar 31, 21 2451 15 Jordan Inconsistent first layer from a cold start to ... Przez TomDD on Mar 31, 21 2250 13 TomDD New Kit won't Run thru Self Test Przez smurpheod on Mar 31, 21 4119 22 Sam Problem printing a thin walled hollow cube Przez Dan Rogers on Mar 30, 21 2690 9 TwoBallScrewB... First layer - too low or too high? Przez wakareva on Mar 30, 21 1772 5 wakareva Lines in print on textured bed in various loca... Przez Diem on Mar 30, 21 1425 6 mgtarallo New here and printed the first item. Overal sa... Przez Clarmrrsn on Mar 29, 21 1362 3 FRANK Random X-offset Przez Clarmrrsn on Mar 29, 21 2346 6 JulietteLhx Hot End Replacement - Covered in Filament Blob Przez bobstro on Mar 29, 21 3629 4 Ed_ATL Strona 73 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: