English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 73 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Thick layer line on same area of multiple prin... Von Dan Rogers on Apr 08, 21 1691 4 tentaclejoe Isolation on the cables near the hotend. Von Zbyszek on Apr 06, 21 1578 7 Zbyszek First print - what is wrong? Von cwbullet on Apr 05, 21 1878 4 OndrejS First layer smaller than second Answered Von Neophyl on Apr 04, 21 2914 2 Christos.Tzer... Screwed up doing assembly, how to solve and wh... Von cwbullet on Apr 03, 21 2274 11 Reas Set up process not starting Von Neophyl on Apr 03, 21 1617 2 grizzly99 Can't print PLA Von Peter M on Apr 03, 21 2072 6 kirkfrey ripples on flat surface PLA Von Peter M on Apr 03, 21 2492 2 kabauter My First print - Any advise? Von Clarmrrsn on Apr 02, 21 1845 8 Djidji Filament Extrusion Test Failure - Hot End Too ... Von Peter M on Apr 02, 21 1746 15 Bill H New to this - First layer not sticking Von Chris W. on Apr 01, 21 1075 5 Ambanja Y carriage noise? Von Dan Rogers on Mar 31, 21 2451 15 Jordan Inconsistent first layer from a cold start to ... Von TomDD on Mar 31, 21 2250 13 TomDD New Kit won't Run thru Self Test Von smurpheod on Mar 31, 21 4119 22 Sam Problem printing a thin walled hollow cube Von Dan Rogers on Mar 30, 21 2690 9 TwoBallScrewB... First layer - too low or too high? Von wakareva on Mar 30, 21 1772 5 wakareva Lines in print on textured bed in various loca... Von Diem on Mar 30, 21 1425 6 mgtarallo New here and printed the first item. Overal sa... Von Clarmrrsn on Mar 29, 21 1362 3 FRANK Random X-offset Von Clarmrrsn on Mar 29, 21 2346 6 JulietteLhx Hot End Replacement - Covered in Filament Blob Von bobstro on Mar 29, 21 3629 4 Ed_ATL Seite 73 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Teilen: