English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 69 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Extruder problem - new printer By cwbullet on May 23, 21 1461 10 Vita Black plastic collet By eng.shaimaa.el... on May 23, 21 3099 20 eng.shaimaa.e... Sloppy Delivery - Getting too big? By cwbullet on May 22, 21 1907 7 Sink filament sensor By cwbullet on May 22, 21 1382 4 wes Print defect mostly along one axis By cwbullet on May 22, 21 1366 4 hamgolfer Repacking Misumi Bearings .. Replacing the fac... By cwbullet on May 21, 21 2232 3 Sink Extruder Body: Stuck screw and Spinning M3NS n... By MinorMatt on May 21, 21 3841 4 Seraphsins First Self-Test Failing at Bed Check By -- on May 20, 21 3024 2 Nyvad Large gaps on the seam Answered By DoctorShtein on May 19, 21 12703 8 DoctorShtein Extruder scoring the upper x-axis smooth rod? By -- on May 18, 21 5142 32 Frank Prusament PETG not sticking to the bed Answered By Felenari on May 18, 21 5038 19 Barca95 First Nozzle Change... advice? By -- on May 18, 21 2231 4 MinorMatt Calibration problem By chris on May 18, 21 1973 5 chris Is this cold pull OK? By cwbullet on May 17, 21 3926 12 Peter M Petg first layer blobs. By Felenari on May 17, 21 3108 6 Felenari Can't pass calibration very sad.... By cwbullet on May 17, 21 2842 13 McShannon Shifted Lines / printing / first layer problem By cwbullet on May 17, 21 3056 9 Tigerentenclu... Rogues gallery of failed prints and reason for... By cwbullet on May 16, 21 2199 6 Jimbo This an under-extrusion issue? By -- on May 16, 21 2509 4 ShuhDonk Preferred PETG test pattern? By cwbullet on May 16, 21 14825 37 CJSHayward Page 69 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: