English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 58 / 216 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Next Topic Title Last Post Views Posts Author First time user running into a filament jam? By thekrakenisme on Aug 30, 21 1138 6 thekrakenisme Super Newbie with PETG By jsw on Aug 30, 21 2837 10 Strangefx First layer, nozzle drags line starts along fo... By DarthRaptor on Aug 29, 21 6191 3 DarthRaptor "Check axes" calibration failed afer upgrade M... By cwbullet on Aug 29, 21 1280 4 TreibAir Workflow with SD card By Neophyl on Aug 28, 21 1465 10 Bryan34 Prusa stopped in a middle of a printing after ... By Azemonsky on Aug 28, 21 949 3 Azemonsky Z calibration failed! after build plate temp s... By cwbullet on Aug 28, 21 3597 21 TarGz layer skip By Dan Rogers on Aug 28, 21 1295 4 Sander Adjusting the height of the PINDA sensor By Bryan34 on Aug 28, 21 3362 5 Bryan34 How can i improve prints? By Pondzik on Aug 27, 21 1130 4 Pondzik Adhesiun problem, calibration issue? By JoanTabb on Aug 25, 21 1408 4 Siggi Bjarnas... Replaced heatbed thermistor now having bed adh... Answered By cwbullet on Aug 25, 21 1331 7 PetervdPerk PLA wont stick to the PEI plater Answered By BrettG on Aug 25, 21 2612 12 Gurīn First prints fine (I think) Triceratops fails ... By RandyM9 on Aug 25, 21 1551 19 navajas is this z banding? loose (or too tight?) x bel... By cwbullet on Aug 24, 21 3414 7 lumbeecheraw7... Gaps around edges By Fredrico on Aug 23, 21 1593 5 Fredrico Newb getting intermittent excessive material By cwbullet on Aug 23, 21 1907 12 LouisB Just prints a blob in the corner By Buffle on Aug 23, 21 1378 6 matthewstokey First Layer Calibration / Benchy Bottom By bobstro on Aug 23, 21 5896 5 Yangorang Noises on all axises By Peter M on Aug 22, 21 1709 5 Jakub Page 58 / 216 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Next Share: