English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 3 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Tytuł Tematu Ostatni Post Widok Posty Author Last Mk3s+ to be built ? Przez Dennis Jay on Apr 17 2328 2 Jws3d Superpinda keeps smacking print Przez Eve on Apr 13 4555 2 CliffordTheRe... Inconsistent first layers after first few prin... Przez Eve on Apr 13 4441 4 Eve Ultrasonic Cleaner on new bearings? Przez TeamADW on Apr 09 5110 8 Bill Marcy Printer Failing Z-Axis Test With No Error Mess... Przez Jake on Mar 21 4574 3 Jake First layer cal is way off Przez Diem on Mar 13 4103 5 Bjerggaard No successful print so far Przez FoxRun3D on Feb 28 3651 4 boricuastock Calibration Wizard question Przez SWAG_4_1if3 on Feb 27 3649 3 SWAG_4_1if3 Whenever I run out of filament - I have to dis... Przez dankat on Feb 25 5114 11 Mattias Fager... Argh! It keeps asking me to unload and reload... Przez Deeb on Feb 22 21188 41 dimprov Priline Carbon Fiber Polycarbonate Not Good Przez 3D2Reality on Feb 22 14568 14 Degreeless_En... Underextrusion / no extrusion at start of each... Przez Green Joe on Feb 20 4620 5 Don Karnage XYZ Calibration Cube Przez Robin_13 on Feb 17 3412 3 Iamcubsman PTFE tube Przez Robin_13 on Feb 17 2180 4 Leo Extruder grub screw loose! Przez Robin_13 on Feb 17 7435 11 Peter M Z banding? Need help Przez Kharnberseker on Feb 17 2832 1 Kharnberseker Is it my nozzle or bed? Przez Topaz Lazarus on Feb 14 2608 1 Topaz Lazarus Fine First layer calibration Przez Diem on Feb 10, 25 2470 9 latot Ground plate messy - first time this problem Przez Fetzke on Feb 09, 25 2662 3 Fetzke Y axis squeeking Przez Haggis McHaggi... on Feb 02, 25 5285 11 Steve Strona 3 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Share: