English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 39 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Requesting advice on first test print after as... Da Gappa on Apr 14, 22 1677 4 Gappa Print gets striations at the end Da cmgreyhounds on Apr 13, 22 1593 4 Platonicsolid Issue with surface quality. Da cmgreyhounds on Apr 13, 22 1675 3 Blagovest First Layer Calibration issues - cannot move n... Da mbiasotti on Apr 13, 22 2946 12 mbiasotti North New Jersey - Assistance needed ( willing... Da CLang on Apr 12, 22 1619 1 CLang First print failed catastrophically Da Thejiral on Apr 11, 22 1461 6 DavidLely Extrusion, bed or hotend issue? Da naaitsab on Apr 11, 22 1485 7 naaitsab Replacing rev. 4 of MK3S extruder motor plate ... Da BearBee on Apr 11, 22 1489 1 BearBee First PLA temp tower issues Da JoanTabb on Apr 11, 22 1612 2 Dracomagus First layer missing lines Da Diem on Apr 10, 22 1357 2 Sainter First print Da Diem on Apr 10, 22 1777 2 Dracomagus Small blobs of filament on first layer Da Diem on Apr 09, 22 1549 2 Sander Incredibly slight hiccup when calibrating on X... Da nikkwong0 on Apr 09, 22 1494 3 nikkwong0 Losing my mind dealing with Selftest Axis Leng... Da Artur5 on Apr 08, 22 1615 5 nikkwong0 XYZ Calibration Failure Da Szymon on Apr 08, 22 1526 4 MattyDread Texture surface fuzzy as Z goes up Da Swiss_Cheese on Apr 08, 22 1726 8 Valmir First Layer Calibration and Questions Da JoanTabb on Apr 06, 22 4044 22 NickSorgio4 lcd screen y axis Da Diem on Apr 05, 22 1531 2 Giladango Different shine on the exterior wall Da Diem on Apr 04, 22 1216 2 Bierqu Hottend Clogged extremely Da Robin on Apr 04, 22 1303 4 M4TTHI45 Pagina 39 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Condividi: