English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 39 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Requesting advice on first test print after as... Przez Gappa on Apr 14, 22 1676 4 Gappa Print gets striations at the end Przez cmgreyhounds on Apr 13, 22 1591 4 Platonicsolid Issue with surface quality. Przez cmgreyhounds on Apr 13, 22 1675 3 Blagovest First Layer Calibration issues - cannot move n... Przez mbiasotti on Apr 13, 22 2946 12 mbiasotti North New Jersey - Assistance needed ( willing... Przez CLang on Apr 12, 22 1619 1 CLang First print failed catastrophically Przez Thejiral on Apr 11, 22 1460 6 DavidLely Extrusion, bed or hotend issue? Przez naaitsab on Apr 11, 22 1485 7 naaitsab Replacing rev. 4 of MK3S extruder motor plate ... Przez BearBee on Apr 11, 22 1489 1 BearBee First PLA temp tower issues Przez JoanTabb on Apr 11, 22 1612 2 Dracomagus First layer missing lines Przez Diem on Apr 10, 22 1357 2 Sainter First print Przez Diem on Apr 10, 22 1777 2 Dracomagus Small blobs of filament on first layer Przez Diem on Apr 09, 22 1549 2 Sander Incredibly slight hiccup when calibrating on X... Przez nikkwong0 on Apr 09, 22 1494 3 nikkwong0 Losing my mind dealing with Selftest Axis Leng... Przez Artur5 on Apr 08, 22 1614 5 nikkwong0 XYZ Calibration Failure Przez Szymon on Apr 08, 22 1526 4 MattyDread Texture surface fuzzy as Z goes up Przez Swiss_Cheese on Apr 08, 22 1726 8 Valmir First Layer Calibration and Questions Przez JoanTabb on Apr 06, 22 4042 22 NickSorgio4 lcd screen y axis Przez Diem on Apr 05, 22 1531 2 Giladango Different shine on the exterior wall Przez Diem on Apr 04, 22 1215 2 Bierqu Hottend Clogged extremely Przez Robin on Apr 04, 22 1303 4 M4TTHI45 Strona 39 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: