English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 34 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Printing problem. No idea what's wrong Przez JoanTabb on Jul 11, 22 1693 9 vsmax6 Suddenly can't load filament seems like someth... Answered Przez jsw on Jul 10, 22 1628 7 pinballmaker first layer issue + left corner not sticking Przez FJNS on Jul 08, 22 17285 18 Jeryco "Pickles" on Filaflex prints Przez Diem on Jul 08, 22 1123 3 Christoph P. New nozzle - First Layer not working Przez Robin on Jul 07, 22 1585 4 earthor Uneven extrusion after troubleshooting Przez Diem on Jul 07, 22 1764 4 doveilgatto First Layer Problem Przez Nate on Jul 07, 22 1488 5 Nate disappointed with the mk3s Przez Diem on Jul 06, 22 1504 6 leandro.pitta All going well until one print... Przez JoanTabb on Jul 04, 22 1462 8 Tango Filament not recognized (any more?) Answered Przez karl-herbert on Jul 04, 22 1341 4 Tom Not quite first print, but possible adjustment... Przez Tango on Jul 02, 22 1257 1 Tango First benchy and ctrlV test, small issues Answered Przez Diem on Jul 02, 22 1630 6 eJar0k Couple hot end questions Przez jmshirley on Jul 01, 22 1194 3 jmshirley 3rd print - not much on the bottom layer Answered Przez Tango on Jun 29, 22 1390 4 Tango Over a day and a half to print this?!? Przez Tango on Jun 28, 22 1622 4 Tango Y axis length error Przez Robin on Jun 26, 22 1355 4 Krashone Just assembled and calibration prints have pro... Przez Robin on Jun 26, 22 4505 23 Tango Starts printing at 23.15mm ?? Przez KikeMarchuet on Jun 25, 22 1652 6 KikeMarchuet Heat bed alignment Przez JoanTabb on Jun 24, 22 1508 4 Nateclaf A vey unhappy experience. Przez Crab on Jun 24, 22 3618 38 Baz Strona 34 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: