English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 21 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Factory installed printer was perfect but now ... Por Extra Fox on Jan 31, 23 1406 4 DTG Complete Parts List and Sourcing for DIY Prusa... Por Drewz989 on Jan 28, 23 4689 2 cpmechenginee... Gcode mod for "extrusion multiplier" and "extr... Por Diem on Jan 26, 23 1655 7 Daniel Selftest error!Please check: Endstops Wiring e... Answered Por Omega-TI on Jan 26, 23 2052 8 Omega-TI Underextrusion on internal layers? Por Runboy on Jan 26, 23 8560 37 DoctorShtein Benchy print failure Answered Por Geo1978 on Jan 25, 23 1109 4 Geo1978 Is normal this noise? Answered Por Andr34 on Jan 25, 23 1317 11 Andr34 Part warping on bed during print? Por mikeolson on Jan 25, 23 1366 5 mikeolson adhesion/warping on flat prints Por JoanTabb on Jan 25, 23 1877 6 cabbage63 Weird whoosh/vader sound after first PETG prin... Answered Por Berbelucha on Jan 24, 23 937 5 Berbelucha „Layer Problem“ Por Neophyl on Jan 24, 23 1149 6 Manuel Hauser Cannot calibrate Z axis Por Manuel Hauser on Jan 24, 23 2766 15 Axey First Print Benchy printer crashed Por Timothy on Jan 23, 23 2827 23 Timothy Making the move from PLA to PETG with a new MK... Por RandyM9 on Jan 23, 23 1276 10 Jason Page Yet another z offset calibration issue .... or... Answered Por erik on Jan 23, 23 1509 8 erik Ajustement sonde/ buse/Z Por adesir on Jan 23, 23 1042 6 Kev My printer, i3 MK3, doesn't seem to recognize ... Por FoxRun3D on Jan 22, 23 2250 10 MrRules too low, too high? Por Buzz on Jan 22, 23 1184 3 Buzz Noise when make first layer Por UnitedStates3 on Jan 22, 23 1288 1 UnitedStates3 PLA Tuning - Stringing, how good does it get? Por RandyM9 on Jan 22, 23 1410 10 Aaron Pigeon Página 21 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Compartir: