English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 211 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Severe Y-Axis Skipping/Shiftin Przez Rosparovac on May 19, 18 1706 2 eric.s32 Help with troubleshooting failed prints Przez Rosparovac on May 19, 18 2469 2 derek.f3 Filament Sensor not working Przez Lups on May 19, 18 1957 3 Lups First Run xyz calibration trouble Przez Webdad on May 19, 18 2016 8 chris.l21 Strange layer problem Przez drkanukie on May 18, 18 1704 4 sven.m5 Y rods are not even after assembly Przez Dreide on May 18, 18 3031 15 Manux XYZ calibration point crash Przez reid.b on May 17, 18 1379 4 jeffrey.r3 Strange wall errors Przez Lups on May 16, 18 1441 3 Lups Dat1darkrai's printer Przez Ian B on May 16, 18 2418 15 dat1darkrai PLA filament "assaulted" the hot end... Przez luca.r on May 16, 18 2019 5 luca.r Very noisy mk3 Przez thrawn86 on May 15, 18 1668 3 Mark McGraw Ugly Surface problem Przez Robin on May 14, 18 3469 9 Chattel XYZ calibration and a ruined bed? Przez Ian B on May 14, 18 3737 9 Gardner New user , calibrating the machine & 1st p... Przez Rosparovac on May 14, 18 2165 4 Dibujor First Layer Problems Przez stahlfabrik on May 14, 18 2060 3 joseph.l6 de-grease and re-grease of linear bearings Przez reid.b on May 13, 18 2562 3 Michael K. First prints taking ~40% longer than expected Przez Olef on May 12, 18 1756 2 Peter Move Z < 1 mm Przez sam.b on May 11, 18 2184 3 sam.b Extruder knocking/ clicking. Przez Joe on May 11, 18 1588 5 Joe Top surface uneven Przez Martin Wolfe on May 10, 18 2013 5 twam Strona 211 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: