English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 210 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Steel sheet holes Przez john.v11 on May 27, 18 4628 4 NM Several problems with kit; Underextrusion; Sou... Przez jacek.l2 on May 26, 18 2002 4 Venthe Is this a problem with my X belt tension? Przez JoanTabb on May 26, 18 1979 5 curt.h Newb, Printed some tests - Can you help me int... Przez Dibujor on May 26, 18 8718 28 Dibujor Loose X and Y axis belts. How to tighten them? Przez Gato on May 25, 18 15681 6 luca.r Go from bad to worse Przez mark.m51 on May 23, 18 1322 1 mark.m51 filament doesnt stick to bed Przez LaPointe on May 22, 18 1476 3 Jákup J. E. Bed level issues Przez LaPointe on May 22, 18 2858 5 Gradivus new kit build: bottom and top layer issues Przez Dibujor on May 22, 18 1997 6 blueicee X-axis shift Przez narloke on May 22, 18 2578 8 narloke Cooling Fan Error Przez Fotoman on May 22, 18 2041 4 Fotoman Replacing the X end motor-idler and tightening... Przez thrawn86 on May 22, 18 2787 2 Oram & Ra... build plate Przez LaPointe on May 21, 18 1382 2 mark.g22 XYZ calibration looks like it finds all 4 poin... Przez jon.k on May 21, 18 3505 10 jon.k Filament Jam Przez christian.m23 on May 21, 18 1746 10 christian.m23 Heat Bed Temperature Przez Olef on May 21, 18 1778 4 Beech76 PETG cold pulls Przez Gato on May 20, 18 26680 7 devilhunter Adhesion issues Przez LaPointe on May 20, 18 1812 5 mark.m51 Use drill for assembly? Przez Gato on May 20, 18 2916 9 Gato extruder clicks and leaves gaps in dispensed f... Przez thrawn86 on May 20, 18 1801 4 dimprov Strona 210 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: