English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 211 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Replacing the X end motor-idler and tightening... Da thrawn86 on May 22, 18 2947 2 Oram & Ra... build plate Da LaPointe on May 21, 18 1605 2 mark.g22 XYZ calibration looks like it finds all 4 poin... Da jon.k on May 21, 18 3768 10 jon.k Filament Jam Da christian.m23 on May 21, 18 1974 10 christian.m23 Heat Bed Temperature Da Olef on May 21, 18 1929 4 Beech76 PETG cold pulls Da Gato on May 20, 18 28273 7 devilhunter Adhesion issues Da LaPointe on May 20, 18 2086 5 mark.m51 Use drill for assembly? Da Gato on May 20, 18 3255 9 Gato extruder clicks and leaves gaps in dispensed f... Da thrawn86 on May 20, 18 1938 4 dimprov Crash detected.. resumed with a layer shift. Da blueicee on May 19, 18 1267 5 dat1darkrai Severe Y-Axis Skipping/Shiftin Da Rosparovac on May 19, 18 1932 2 eric.s32 Help with troubleshooting failed prints Da Rosparovac on May 19, 18 2656 2 derek.f3 Filament Sensor not working Da Lups on May 19, 18 2172 3 Lups First Run xyz calibration trouble Da Webdad on May 19, 18 2199 8 chris.l21 Strange layer problem Da drkanukie on May 18, 18 1921 4 sven.m5 Y rods are not even after assembly Da Dreide on May 18, 18 3377 15 Manux XYZ calibration point crash Da reid.b on May 17, 18 1545 4 jeffrey.r3 Strange wall errors Da Lups on May 16, 18 1667 3 Lups Dat1darkrai's printer Da Ian B on May 16, 18 2739 15 dat1darkrai PLA filament "assaulted" the hot end... Da luca.r on May 16, 18 2185 5 luca.r Pagina 211 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Condividi: