English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 200 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Bad printing quality only on the other side of... Da aapo.l on Aug 01, 18 1798 3 aapo.l Torque amount on Mk3 Frame Da francis.f2 on Aug 01, 18 1912 3 francis.f2 Print supports don't hold Da Knickohr on Jul 31, 18 1762 6 Ferllings Top layers rough and lack detail Da toaf on Jul 31, 18 1510 4 simon.b19 X-axis shift when printing on right-hand side ... Da AndrewH on Jul 31, 18 1349 3 AndrewH Prints tend to shift in the middle of a long j... Da nathan0876 on Jul 30, 18 1380 4 dennis.c2 Surface finish issues with MK3 kit (S3D and Sl... Da bobstro on Jul 30, 18 2648 4 Ray First layer quality and MK3 technical specific... Da RufusClupea on Jul 30, 18 2323 4 JuLu Newbie 1st layer calibration Da Larry on Jul 30, 18 1801 6 Larry Fan nozzle comes loose after several hours Da JMcK on Jul 30, 18 1937 3 AndrewH MatterHackers Build Series Settings? Da m00dawg on Jul 29, 18 1949 3 m00dawg Burned blobs and oozing Da Gato on Jul 29, 18 4808 6 Robert Stárek Forgive me if this has already been solved (is... Da thrawn86 on Jul 29, 18 1424 2 sean.t2 Critique, Please... Da RufusClupea on Jul 29, 18 649 5 RufusClupea Extrusion trouble Da Hudson_t on Jul 28, 18 1702 6 Hudson_t The printer just keeps forgetting...! Da JoanTabb on Jul 27, 18 802 5 andrew.s59 New user trying to set up Da Pathogen on Jul 27, 18 1141 3 brian.p22 Using thread lock on frame Da Pathogen on Jul 27, 18 4249 8 WaterboyMK3 First Benchy got bumped, snapping off my fan s... Da bobstro on Jul 27, 18 1762 2 RolandSvL Stuck in the First Cal. Layer zone Da alex.g10 on Jul 25, 18 3180 15 alex.g10 Pagina 200 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: