English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 2 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Tytuł Tematu Ostatni Post Widok Posty Author Old STL file needed Przez Neophyl on Aug 02 2799 3 Gavin Melvill... First layer starts then z calibration loop Przez Diem on Jul 25 2718 2 Juan David Horizontal layer lines (Z-Banding?) Przez Aaron O on Jul 18 16146 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered Przez printing_stuff on Jul 10 3184 9 printing_stuf... I bought a used printer and can't tell if it's... Przez PrusaNewbie on Jul 10 3991 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Przez HYspd on Jul 06 4529 2 Fourninetysix Z-Axis noise. Is this normal? Przez Robin_13 on Jun 26 13818 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Przez Kenyiro34 on Jun 20 3173 8 Blippio Test print doesn't print straight lines Przez JoanTabb on May 30 4029 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Przez Criptop on May 30 5825 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Przez Cwhite534 on May 23 3559 7 jhk22 2nd Print with PLA takeoff from the plate Przez JoanTabb on May 15 3923 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Przez gigiga on May 06 5886 10 SeppoTakalo First layer PETG not sticking to print bed Answered Przez tom_streeter on Apr 30 62891 26 Chuck Unable to Autoload Filament Przez CodeCage on Apr 19 14868 9 gmbarton Last Mk3s+ to be built ? Przez Dennis Jay on Apr 17 2270 2 Jws3d Superpinda keeps smacking print Przez Eve on Apr 13 4501 2 CliffordTheRe... Inconsistent first layers after first few prin... Przez Eve on Apr 13 4368 4 Eve Ultrasonic Cleaner on new bearings? Przez TeamADW on Apr 09 4941 8 Bill Marcy Printer Failing Z-Axis Test With No Error Mess... Przez Jake on Mar 21 4471 3 Jake Strona 2 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Share: