English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 2 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author First layer starts then z calibration loop Por Diem on Jul 25 2716 2 Juan David Horizontal layer lines (Z-Banding?) Por Aaron O on Jul 18 16120 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered Por printing_stuff on Jul 10 3180 9 printing_stuf... I bought a used printer and can't tell if it's... Por PrusaNewbie on Jul 10 3986 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Por HYspd on Jul 06 4528 2 Fourninetysix Z-Axis noise. Is this normal? Por Robin_13 on Jun 26 13794 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Por Kenyiro34 on Jun 20 3166 8 Blippio Test print doesn't print straight lines Por JoanTabb on May 30 4026 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Por Criptop on May 30 5821 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Por Cwhite534 on May 23 3552 7 jhk22 2nd Print with PLA takeoff from the plate Por JoanTabb on May 15 3919 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Por gigiga on May 06 5874 10 SeppoTakalo First layer PETG not sticking to print bed Answered Por tom_streeter on Apr 30 62807 26 Chuck Unable to Autoload Filament Por CodeCage on Apr 19 14839 9 gmbarton Last Mk3s+ to be built ? Por Dennis Jay on Apr 17 2269 2 Jws3d Superpinda keeps smacking print Por Eve on Apr 13 4499 2 CliffordTheRe... Inconsistent first layers after first few prin... Por Eve on Apr 13 4363 4 Eve Ultrasonic Cleaner on new bearings? Por TeamADW on Apr 09 4930 8 Bill Marcy Printer Failing Z-Axis Test With No Error Mess... Por Jake on Mar 21 4464 3 Jake First layer cal is way off Por Diem on Mar 13 4023 5 Bjerggaard Página 2 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: