English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 197 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Creaking noise on x-axis Przez Ed Barton on Aug 15, 18 2599 5 Ed Barton First layer 'bubbles' and failed infill Przez thrawn86 on Aug 15, 18 2390 4 Andrew Read Colorfabb HT filament printing issue Przez darKing on Aug 15, 18 2281 2 aapo.l Assembled vs Kit Przez RufusClupea on Aug 15, 18 11825 22 Phil After 3 months with MK3 kit Przez nickolay.d on Aug 14, 18 1880 2 nickolay.d MK3 kit print issue Przez Bytor on Aug 14, 18 1619 2 Byulos any guide to find proper belt tension? Przez doa on Aug 13, 18 9035 10 doa How exact should "Step 10" (Geometry... Przez RH_Dreambox on Aug 13, 18 3003 10 Idus Right Side and Front Side of Bed too squished Przez jprochnow on Aug 13, 18 1266 1 jprochnow New MK3 Kit build with inop Z axis motor Przez JoanTabb on Aug 12, 18 1675 4 Pit Bull Dogs fucked up prints after nozzle change Przez JoanTabb on Aug 12, 18 1451 5 max.b5 Curious bed calibration issue Przez Olef on Aug 12, 18 1505 5 dgalanaud Preheating the Nozzle without the Heatbed - po... Przez JoanTabb on Aug 11, 18 1954 6 al.g Worked great and then not so great... Przez mrdutchy on Aug 10, 18 976 9 mrdutchy What is the point of putting in the Nylon Fila... Przez RufusClupea on Aug 10, 18 3216 3 suzanne.w Step 30 Inserting the Nylon Filament Przez RufusClupea on Aug 10, 18 2750 2 suzanne.w First print, very wispy then all over the plac... Przez bobstro on Aug 10, 18 1588 2 david.m122 live z petg Przez themzlab on Aug 09, 18 2269 4 gatonini@zoom... Fail xyz - Please consult the manual. Przez JoanTabb on Aug 09, 18 1013 2 Dev O Some issues with printing after thermistor swa... Przez nuno.q on Aug 09, 18 1240 6 nuno.q Strona 197 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: