English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 197 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Creaking noise on x-axis Por Ed Barton on Aug 15, 18 2599 5 Ed Barton First layer 'bubbles' and failed infill Por thrawn86 on Aug 15, 18 2390 4 Andrew Read Colorfabb HT filament printing issue Por darKing on Aug 15, 18 2281 2 aapo.l Assembled vs Kit Por RufusClupea on Aug 15, 18 11825 22 Phil After 3 months with MK3 kit Por nickolay.d on Aug 14, 18 1880 2 nickolay.d MK3 kit print issue Por Bytor on Aug 14, 18 1619 2 Byulos any guide to find proper belt tension? Por doa on Aug 13, 18 9035 10 doa How exact should "Step 10" (Geometry... Por RH_Dreambox on Aug 13, 18 3003 10 Idus Right Side and Front Side of Bed too squished Por jprochnow on Aug 13, 18 1266 1 jprochnow New MK3 Kit build with inop Z axis motor Por JoanTabb on Aug 12, 18 1675 4 Pit Bull Dogs fucked up prints after nozzle change Por JoanTabb on Aug 12, 18 1451 5 max.b5 Curious bed calibration issue Por Olef on Aug 12, 18 1505 5 dgalanaud Preheating the Nozzle without the Heatbed - po... Por JoanTabb on Aug 11, 18 1954 6 al.g Worked great and then not so great... Por mrdutchy on Aug 10, 18 976 9 mrdutchy What is the point of putting in the Nylon Fila... Por RufusClupea on Aug 10, 18 3216 3 suzanne.w Step 30 Inserting the Nylon Filament Por RufusClupea on Aug 10, 18 2750 2 suzanne.w First print, very wispy then all over the plac... Por bobstro on Aug 10, 18 1588 2 david.m122 live z petg Por themzlab on Aug 09, 18 2269 4 gatonini@zoom... Fail xyz - Please consult the manual. Por JoanTabb on Aug 09, 18 1013 2 Dev O Some issues with printing after thermistor swa... Por nuno.q on Aug 09, 18 1240 6 nuno.q Página 197 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: