Notifiche
Cancella tutti

PTFE tube suppliers  

  RSS
John
 John
(@john-6)
Reputable Member
PTFE tube suppliers

Hi Im looking to order some PFTE tube ( OD 4mm ID 2mm) - Firstly the only supplier I have found in Australia is very expensive compared to Amazon. Unfortunately Amazon won't ship this to Australia. Any supplier suggestions welcome. Also ideally I would like transparent tube but not essential.

i3 Mk3 [aug 2018] upgrade>>> i3MK3/S+[Dec 2023]

Postato : 03/06/2019 4:56 am
John
 John
(@john-6)
Reputable Member
Topic starter answered:
RE: PTFE tube suppliers

bump

i3 Mk3 [aug 2018] upgrade>>> i3MK3/S+[Dec 2023]

Postato : 04/06/2019 8:24 am
BillC
(@billc)
Reputable Member
RE: PTFE tube suppliers

https://e3d-online.com/resellers

 

Bill
Tagaytay City, Philippines
Founder member of Philippines Prusa Printer Owners FB Group
Sponsor Pillars of God Academy in Bacoor

Postato : 05/06/2019 11:05 am
Antimix
(@antimix)
Reputable Member
RE: PTFE tube suppliers

I just bough some PTFE on Amazon, and I paid much less.

I bough the PTFE external 4mm diameter PFTE with internal 3mm (used for the 3mm filament) to allow enough space for the 1.75mm filament on the MMU2S to avoid blocks.

 

Postato : 14/06/2019 7:30 pm
John
 John
(@john-6)
Reputable Member
Topic starter answered:
RE: PTFE tube suppliers

For some reason amazon wouldn’t ship this but I found a local supplier who was a reasonable price. 

i3 Mk3 [aug 2018] upgrade>>> i3MK3/S+[Dec 2023]

Postato : 14/06/2019 11:08 pm
PJR
 PJR
(@pjr)
Antient Member Moderator
RE: PTFE tube suppliers

You do need to be careful with PTFE tubing.

Most tubing found on Amazon and eBay are "no brand" Chinese with poor tolerances and eccentricity, and I even bought some which turned out to be regular plastic tubing which was folded and kinked for posting 🙁

Better to pay a bit more and get decent branded stuff, if possible.

Also, I would not have an ID of greater than 2.5mm; if the walls are too thin, they cannot be held in place with the Festos.

 

Peter

Please note: I do not have any affiliation with Prusa Research. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage…

Postato : 15/06/2019 9:04 am
egalanos
(@egalanos)
Active Member
RE: PTFE tube suppliers
Posted by: john.h68

For some reason amazon wouldn’t ship this but I found a local supplier who was a reasonable price. 

Which supplier did you use in Australia? I got my MMU the other week and some of my existing filament can't pass through. Sigh.

Postato : 15/08/2019 12:12 pm
rmm200
(@rmm200)
Noble Member
RE: PTFE tube suppliers
Posted by: PJR

You do need to be careful with PTFE tubing.

Most tubing found on Amazon and eBay are "no brand" Chinese with poor tolerances and eccentricity, and I even bought some which turned out to be regular plastic tubing which was folded and kinked for posting 🙁

Better to pay a bit more and get decent branded stuff, if possible.

Also, I would not have an ID of greater than 2.5mm; if the walls are too thin, they cannot be held in place with the Festos.

 

Peter

Would love to know a recommended brand for PTFE, available in USA.

Amazon would be a plus...

It is somewhat discouraging to hear some rolls of Prusament won't pass through Prusa supplied PTFE.

We can't do worse than that, cutting our own.

Also what is a favorite jig for cutting PTFE? I know Bear has one.

Postato : 24/08/2019 5:54 pm
John
 John
(@john-6)
Reputable Member
Topic starter answered:
RE: PTFE tube suppliers
Posted by: egalanos
Posted by: john.h68

For some reason amazon wouldn’t ship this but I found a local supplier who was a reasonable price. 

Which supplier did you use in Australia? I got my MMU the other week and some of my existing filament can't pass through. Sigh.

Hi egalonous. 

https://www.bilby3d.com.au

My project got put on hold so I haven’t actually tried it yet. 

i3 Mk3 [aug 2018] upgrade>>> i3MK3/S+[Dec 2023]

Postato : 24/08/2019 11:16 pm
Condividi: