English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Page 120 / 196 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Suivant Titre du sujet Dernier message Nombre de vues Messages Author PC Blend Print Layer Shift Par cwbullet on Jul 31, 21 4416 7 Nikolaus Stei... Pruša Basic Filament unusable Par Peter M on Jul 29, 21 3576 9 Tom Hotend fan not spinnig after slightly touching... Par bobstro on Jul 27, 21 2209 3 Santiago Prints of mine gone from my prints Par cwbullet on Jul 27, 21 1523 2 MatsErik Why not twice as long?? Answered Par Dan on Jul 27, 21 2131 3 Dan Filament sensor Par cwbullet on Jul 27, 21 2097 3 movingpix Curious about members with more than one print... Par cwbullet on Jul 27, 21 4056 15 Brad Widgets/buttons in Print summary Par JMcK on Jul 27, 21 2273 3 JMcK Measured correlation between layer height, fir... Par FoxRun3D on Jul 25, 21 2634 2 bumgarb42 Prusaslicer Q Par Basic on Jul 25, 21 2671 13 Basic Prusaprinters.org goes nuts when scrolling thr... Par jsw on Jul 25, 21 2655 12 marcospelde New forum for prusaprinters.org website? Par bobstro on Jul 24, 21 2129 3 FoxRun3D How delete collections Par adesir on Jul 24, 21 2693 2 DaveGadgeteer What should be the width of the first layer ca... Par bobstro on Jul 23, 21 8009 8 jedwards Right filament/shore hardness for vacuum nozzl... Par TJH on Jul 23, 21 3494 6 Alpha Is there censorship for adult material? Par Nikolai on Jul 22, 21 2111 2 Wilson65 Blocked supports ignored? Par Swiss_Cheese on Jul 21, 21 1974 5 Basic Even holes are of the same size, those at the ... Par Dan Rogers on Jul 18, 21 2751 3 prusanewuser Help!! Problems with print bed Par Corine on Jul 16, 21 2184 1 Corine How to avoid removing outer perimeters when re... Par FoxRun3D on Jul 16, 21 2748 4 prusanewuser Page 120 / 196 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Suivant Partager :