English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Strona 120 / 196 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Następny Tytuł Tematu Ostatni Post Widok Posty Author Hotend fan not spinnig after slightly touching... Przez bobstro on Jul 27, 21 2200 3 Santiago Prints of mine gone from my prints Przez cwbullet on Jul 27, 21 1523 2 MatsErik Why not twice as long?? Answered Przez Dan on Jul 27, 21 2130 3 Dan Filament sensor Przez cwbullet on Jul 27, 21 2095 3 movingpix Curious about members with more than one print... Przez cwbullet on Jul 27, 21 4054 15 Brad Widgets/buttons in Print summary Przez JMcK on Jul 27, 21 2272 3 JMcK Measured correlation between layer height, fir... Przez FoxRun3D on Jul 25, 21 2633 2 bumgarb42 Prusaslicer Q Przez Basic on Jul 25, 21 2671 13 Basic Prusaprinters.org goes nuts when scrolling thr... Przez jsw on Jul 25, 21 2652 12 marcospelde New forum for prusaprinters.org website? Przez bobstro on Jul 24, 21 2129 3 FoxRun3D How delete collections Przez adesir on Jul 24, 21 2689 2 DaveGadgeteer What should be the width of the first layer ca... Przez bobstro on Jul 23, 21 8003 8 jedwards Right filament/shore hardness for vacuum nozzl... Przez TJH on Jul 23, 21 3489 6 Alpha Is there censorship for adult material? Przez Nikolai on Jul 22, 21 2110 2 Wilson65 Blocked supports ignored? Przez Swiss_Cheese on Jul 21, 21 1973 5 Basic Even holes are of the same size, those at the ... Przez Dan Rogers on Jul 18, 21 2738 3 prusanewuser Help!! Problems with print bed Przez Corine on Jul 16, 21 2175 1 Corine How to avoid removing outer perimeters when re... Przez FoxRun3D on Jul 16, 21 2745 4 prusanewuser Has anyone experimented with using a speedomet... Przez xenon on Jul 15, 21 2169 4 Sean Roach Prusa mk3s+ Z behavior Answered Przez Lichtjaeger on Jul 15, 21 1823 2 Basic Strona 120 / 196 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Następny Share: