English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 48 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Tytuł Tematu Ostatni Post Widok Posty Author warping , lifting prints Przez kenatno10 on May 21, 20 1528 1 kenatno10 Colorisation with transparant filament Answered Przez Crawlerin on May 20, 20 1431 4 Oxygen Prusa Mini freezes at 95% on Purge Przez MCMuckle on May 19, 20 2565 4 3DPrintsbyChr... Trying to identify layer shift in x-axis Przez LE3D on May 19, 20 2230 3 LE3D Mesh Bed Leveling Fails Przez criageek on May 19, 20 2060 3 criageek Mini print evaluation Przez Josh on May 17, 20 1251 1 Josh Heavy Stringing Przez JoanTabb on May 17, 20 2228 2 kairikitty Extruder clicking during support material prin... Przez kevman on May 17, 20 1536 1 kevman Large Live-Z but good first layer Przez Milos V. on May 17, 20 2339 6 jaychatt Assembly Step 14 - M3x20 won't engage Przez IamPeterYouAre... on May 15, 20 2545 6 griffinrevell Z Calibration failure Przez karl-herbert on May 14, 20 1479 3 Glen Childres... Prusa mini Assembly issue with XZ electronics ... Przez 3Dprintedgr on May 14, 20 2146 5 TechGuy2020 First time setup best practices Przez Codetoad on May 11, 20 1630 3 Codetoad Some blobbing happening with prints. Przez 3Dprintedgr on May 10, 20 1791 2 kevman Cannot get to the PTFE Tube Przez reddadsteve on May 07, 20 2121 7 ari.s.friedma... Troubles with underextrusion Przez bobc on May 07, 20 2614 9 Jens Kjeldste... Y belt not tensionned Przez Ordimans on May 03, 20 1870 3 Ordimans Wiring for attaching Y AXIS motor does not mat... Przez 3Dprintedgr on May 03, 20 1877 4 grabnerwg@gma... Wiring for attaching Y AXIS motor does not mat... Przez grabnerwg@gmai... on May 03, 20 1730 5 grabnerwg@gma... Don't tighten the Z-Axis screws to much Przez dargul on May 02, 20 2055 1 dargul Strona 48 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Share: